查询词典 heat-unit

According to the present situations of the two production lines and the temperature needed by the producing technics of the heat-exchanger , using the numerical simulation with the Airpark software to analyze the reason why the cooling system can not meet the technicals requirement; with the heat transfer theory computation based on the heat transfer principle, the technical parameters of the cooling sect refer to the system technic and configuration are obtained. That are made for reasonable organization of the airflow of the cooling system and the new cooling equipment achieving the technical requirement. At the same time, it will ease the thermal pollution of the circumjacent environment and improve IAQ of the workshop

根据某厂两条换热器生产流水线的现状和冷却降温的工艺要求，用Airpark 软件进行数值模拟，分析了冷却系统无法满足工艺要求的原因；运用传热学原理进行了设备与环境的传热理论分析和计算，分析了冷却系统无法满足工艺要求的原因，得出了改造所需要的技术与结构参数，并对冷却系统进行合理布局与气流组织，使新的冷却系统发挥了应有的作用，满足了生产工艺的要求，同时也减轻了生产环境的热污染，提高了环境的空气品质。

The aluminum groove used for heat dissipation is extrusion molding by 6030 aluminum ,and through anodize precessing technic ,with scientific struction for heat dissipation design ,which can solve the problem of heat dissipation efficiently , and can longer the life-span of LEDs , In addition ,the driver power utilize constant current IC driver ,which can asure the precise of power output and the stability during the couse of using .

散热铝槽采用6063铝挤出成型，经过阳极氧化等加工工艺处理，加上科学的散热结构设计，有效解决灯管散热难的问题，大大提高 LED 使用寿命。驱动电源采用恒流 IC 驱动方案，电流输出的精度高，确保 LED 使用的稳定性。

The results show that the glass-ceramics with fibroid structure is produced after definite heat treatment, the main crystallization phase is hedenbergite and anorthite is the minor crystallization phase. The optimal process of heat treatment shows as follows: the nucleation temperature is 850 ℃ and hold time is 100 min, and the crystallization temperature is 980 ℃ and hold time is 80 min. With increasing heat treatment temperature, the FT-IR absorption bands appear obvious split, the aluminum-oxide polyhedron in the glass network changes from [AlO4] to [AlO6]. The titanium ion in the glass network gradually transforms to the 6-coordinated, moreover forms minicrystal of MgTi2O5 and Fe2TiO4 which provides the position of heterogeneous nucleation for the growth of crystal.

结果表明：在一定的热处理条件下可以以基础玻璃制备出主晶相为钙铁透辉石，次晶相为钙长石的纤维状结构的微晶玻璃；最佳的热处理工艺为：850 ℃核化100 min，980 ℃晶化80 min；随着热处理温度的升高，红外吸收带发生明显的分裂；玻璃结构中的[AlO4]向[AlO6]转化；网络结构中的钛离子逐渐转变为六配位，形成微晶相——钛酸镁和钛铁晶石，为晶体的生长提供非均匀形核位置。

Thermal models of parallel moving heat source, oblique moving heat source, and circle arc moving heat source are set up and analyzed.

采用均布热源建立平面移动热源模型、倾斜运动热源模型和弧形热源模型，并进行了分析。

The effect of heat source location on the heat transfer of an axially grooved heat pipe was investigated.

探讨了轴向槽道热管垂直安装时热源位置的不同对热管工作特性的影响。

If the heat exchangers are well designed and can supply the heat flux needed for convective heat transfer, then the engine will produce power in proportion to the mean pressure, as predicted by the West number, and Beale number.

改变气体温度会引起相应的变化，气体压力，而运动的活塞造成的天然气将轮流扩大和压缩。气体的行为如下描述了天然气的法律，说明气体的压力，温度和体积是有关系的。

The influence of those main design parameterssuch as evaporation saturation temperature t_s、heat dissipated power Q and charge ofworking fluid L on the temperature distribution of evaporation"s bottom and boiling heat transfer inside the evaporation has been calculated and analyzed concretely. The method that uses channels to enhance boiling heat transfer of evaporation"s bottom has also been analyzed and calculated preliminarily.

具体计算和分析了蒸发饱和温度t_s、散热功率Q和充液量L等主要设计参数对蒸发段底面温度分布和蒸发段内部沸腾传热特性的影响，对用槽道强化蒸发段底面沸腾换热也做了初步的数值计算和分析。

Based on detailedly analyzing the application and development of plastic heat exchangers at home and abroad, one approach was advanced that by substituting plastic heat exchanger made of thin wall and canaliculus PTFE plastic tube for the metal heat exchanger of traditional lithium bromide absorption cooler.

本文在对国内外塑料换热器的应用、发展进行详尽分析的基础上，提出采用薄壁小管径聚四氟乙烯塑料管制成的塑料换热器代替传统的溴化锂吸收式制冷机中的金属换热器，制作一台塑料管溴化锂吸收式制冷机及其实验系统的课题。

The Φ(subscript PSⅡ), Fv/Fm and qP were increased but qN was decreased with increasing of chlorophyll a, the rate of heat dissipation was increased with the increasing of chlorophyll b, and the carotinoid increasing enhanced the rate of heat dissipation of dryland and carbon assimilation of irrigated cultivar The Φ(subscript PSⅡ) and qN of dryland cultivar treated by control were higher than that of irrigated cultivar in jointing stage significant, indicating that the characteristics of drought-resistantce of winter wheat could be displayed in the jointing stage, and the drought-resistant capability could be increased by enhancing the practical photochemistry efficiency and heat dissipation in jointing stage.

拔节期对照处理的旱地品种的Φ和qN显著高于水地品种，在该时期品种抗旱性差异表现较为明显，能够通过提高光合机构实际光化学效率和热耗散来增强光合机构对干旱的适应能力。

In order to meet the requirement of the Collector ring dipole superconducting magnet of FAIR in the process of operation, meanwhile, and to ensure the heat loads coming from the support structures to be lower than the design demands, the 3D models of support structures have been constructed with CATIA, then the calculation of low-temperature heat-load and the structure analysis have been done with ANSYS, the support structure material, 316LN+G10, is decided according to the heat-load calculation and the structure optimization, these results are necessary for manufacturing the formal magnet.

为保证FAIR收集环(Collector ring-CR)超导二极磁体工作过程中的磁场位形符合设计要求，同时保证由磁体支撑带来的热负荷小于设计要求，用CATIA软件建立了不同结构的磁体支撑3D模型，并用ANSYS有限元分析软件对建立的模型进行了低温热负荷分析和结构分析。通过比较分析的结果和对磁体支撑结构进行的进一步优化，确定了316LN+G10材料的支撑结构，为收集环超导二极磁体工程制造提供了参考。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐