查询词典 heat-regulating

To investigate the thermal protection effects of a heat sinking vest with phase-change material in high-temperature and high-humidity environment and the feasibility of numerical computation of heat transfer to the vest,based on the analysis of heat and mass transfer characteristic about the accouterments,a thermodynamic model was set up with the enthalpy method.

为了研究相变材料降温服在高温高湿条件下的热防护性能和相变材料数值计算方法应用于降温服传热计算的可行性，在分析服装传热传质特点及计算方法的基础上，利用焓值分析法对服装中的相变材料建立传热模型，在整个区域建立统一的能量方程，在区域结点进行离散，并进行隐式求解，得到焓的分布。

To investigate the thermal protection effects of a heat sinking vest with phase-change material in high-temperature and high-humidity environment and the feasibility of numerical computation of heat transfer to the vest, based on the analysis of heat and mass transfer characteristic about the accouterments, a thermodynamic model was set up with the enthalpy method. The uniform energy equation was constructed for the whole domain, and the implicit difference equation was used in every node, the distribution of enthalpy was solved by numerical method.

为了研究相变材料降温服在高温高湿条件下的热防护性能和相变材料数值计算方法应用于降温服传热计算的可行性，在分析服装传热传质特点及计算方法的基础上，利用焓值分析法对服装中的相变材料建立传热模型，在整个区域建立统一的能量方程，在区域结点进行离散，并进行隐式求解，得到焓的分布。

Thus, the heat content from the waste gases from blast heating apparatus or those arising in the afterburning of waste gas flows from tunnel driers for the removal of solvent residues can be fed back into the process via a heat transfer medium circuit to preheat the fuels and fuel air or to heat up the material to be dried.

因此，来自于废气/加热设备/燃烧形成的热气流/移走废弃的隧道干燥设备等的热量可以通过一个闭路循环的导热油把热量循环利用或者用来加热需要干燥的物质。

According to the present situations of the two production lines and the temperature needed by the producing technics of the heat-exchanger , using the numerical simulation with the Airpark software to analyze the reason why the cooling system can not meet the technicals requirement; with the heat transfer theory computation based on the heat transfer principle, the technical parameters of the cooling sect refer to the system technic and configuration are obtained. That are made for reasonable organization of the airflow of the cooling system and the new cooling equipment achieving the technical requirement. At the same time, it will ease the thermal pollution of the circumjacent environment and improve IAQ of the workshop

根据某厂两条换热器生产流水线的现状和冷却降温的工艺要求，用Airpark 软件进行数值模拟，分析了冷却系统无法满足工艺要求的原因；运用传热学原理进行了设备与环境的传热理论分析和计算，分析了冷却系统无法满足工艺要求的原因，得出了改造所需要的技术与结构参数，并对冷却系统进行合理布局与气流组织，使新的冷却系统发挥了应有的作用，满足了生产工艺的要求，同时也减轻了生产环境的热污染，提高了环境的空气品质。

The aluminum groove used for heat dissipation is extrusion molding by 6030 aluminum ,and through anodize precessing technic ,with scientific struction for heat dissipation design ,which can solve the problem of heat dissipation efficiently , and can longer the life-span of LEDs , In addition ,the driver power utilize constant current IC driver ,which can asure the precise of power output and the stability during the couse of using .

散热铝槽采用6063铝挤出成型，经过阳极氧化等加工工艺处理，加上科学的散热结构设计，有效解决灯管散热难的问题，大大提高 LED 使用寿命。驱动电源采用恒流 IC 驱动方案，电流输出的精度高，确保 LED 使用的稳定性。

The results show that the glass-ceramics with fibroid structure is produced after definite heat treatment, the main crystallization phase is hedenbergite and anorthite is the minor crystallization phase. The optimal process of heat treatment shows as follows: the nucleation temperature is 850 ℃ and hold time is 100 min, and the crystallization temperature is 980 ℃ and hold time is 80 min. With increasing heat treatment temperature, the FT-IR absorption bands appear obvious split, the aluminum-oxide polyhedron in the glass network changes from [AlO4] to [AlO6]. The titanium ion in the glass network gradually transforms to the 6-coordinated, moreover forms minicrystal of MgTi2O5 and Fe2TiO4 which provides the position of heterogeneous nucleation for the growth of crystal.

结果表明：在一定的热处理条件下可以以基础玻璃制备出主晶相为钙铁透辉石，次晶相为钙长石的纤维状结构的微晶玻璃；最佳的热处理工艺为：850 ℃核化100 min，980 ℃晶化80 min；随着热处理温度的升高，红外吸收带发生明显的分裂；玻璃结构中的[AlO4]向[AlO6]转化；网络结构中的钛离子逐渐转变为六配位，形成微晶相——钛酸镁和钛铁晶石，为晶体的生长提供非均匀形核位置。

Thermal models of parallel moving heat source, oblique moving heat source, and circle arc moving heat source are set up and analyzed.

采用均布热源建立平面移动热源模型、倾斜运动热源模型和弧形热源模型，并进行了分析。

In the light of cost index and pollution degree, the characteristics of kinds of pulp are analyzed in detail, and the GP pulp which is low cost, high-yield, no-pollution is chosen as the material of tableware. Based on material element analyzed, shaping technology is designed, the to and for single plane shaping equipment which is high shaping quality, high production efficiency and is easy to automatize is chosen. All kinds of measure are taken to solve the problems which are inequality in the shaping process of GP pulp, and dosage which matches with GP pulp is chosen. Some ways of fixing shape and heat up are analyzed, the technology of saving energy of heat pressing to fix shape being composed of oil heat and only one fixed shape in the mold is applied, with which it is high production efficiency, low cost to fix shape effectively, which saves energy 30 percent. In order to make the production line meet with material of GP pulp, measure are taken to solve the problem of pulp adhered to netlike molding which can lead to carry material difficult, the structure of fully automatic equipment is renovated, the loaded beam is optimizationally designed to make equipment structure compactand improve location precision and products quality. According to technologic flow and actual characteristic, Omron PLC is chosen as the core of the control system, proximity switch as detect unit take the place of touch switch, software is designed reasonably according to time order figure, hardware is simplified, the reliability of system is advanced, the stability of system is assured to make production order. Intelligence neuron PID system is studied theoretically which is made up of both neuron with self-organizing and self-learning function and ordinary PID with the characteristic of the simple structure and high stability, which can automatically tune the parameter with the change of system parameter, remain perfect performance.

按成本指标和污染程度分析各浆料的特点，选择低成本、高得率、无污染的磨石机械浆为原料，在原料组分分析的基础上，设计成型工艺，选择成型质量好、生产率高、易实现自动化的往复式单板成型机，采取各种措施解决GP浆成型不均匀的问题及选择与机械浆相匹配的助剂；分析几种定型方式和加热方式，采用定型效果好、生产率高、成本低的油加热与模内一次性定型相结合的热压定型节能技术，节能30％；为了使生产线适应磨石机械浆原料，采取相应措施解决由于粘网造成物料转移困难，对全自动设备结构进行改进设计，着重对物料传送系统的关键部件——承载梁的进行优化设计，使设备更加紧凑合理，提高设备的定位精度和产品质量；根据生产线工艺流程和现场特点，选用OMRON CPM1A型PLC为主核心，接近开关作为检测元件，替代有触点开关，选用可编程终端代替常规面板按扭，并按照时序图科学合理地设计软件，有效地简化系统硬件构成，提高系统的可靠性，保证系统的稳定性，从而使生产更加通畅有序；从理论上探索将神经元应具有的自组织、自学习要求与PID控制结构简单、稳定性好的全自动纸浆模塑餐具生产线的研究特点结合起来，构成神经元自适应PID控制器，当参数的变化时，系统能自行参数整定，保持优良的工作性能指标，满足实际需求。

The effect of heat source location on the heat transfer of an axially grooved heat pipe was investigated.

探讨了轴向槽道热管垂直安装时热源位置的不同对热管工作特性的影响。

If the heat exchangers are well designed and can supply the heat flux needed for convective heat transfer, then the engine will produce power in proportion to the mean pressure, as predicted by the West number, and Beale number.

改变气体温度会引起相应的变化，气体压力，而运动的活塞造成的天然气将轮流扩大和压缩。气体的行为如下描述了天然气的法律，说明气体的压力，温度和体积是有关系的。

Diabetes is a social disease that affects several million people worldwide.

糖尿病是一个社会性疾病，全世界有数百万人罹患此病。

I'll call you on Friday to see if we can reschedule our luncheon meeting at your convenience.

我星期五会给您打电话在您方便的时候我们重新安排我们的午餐约会。