英语人>网络例句>heat-exhaustion 相关的网络例句
heat-exhaustion相关的网络例句

查询词典 heat-exhaustion

与 heat-exhaustion 相关的网络例句 [注:此内容来源于网络,仅供参考]

The results show that the glass-ceramics with fibroid structure is produced after definite heat treatment, the main crystallization phase is hedenbergite and anorthite is the minor crystallization phase. The optimal process of heat treatment shows as follows: the nucleation temperature is 850 ℃ and hold time is 100 min, and the crystallization temperature is 980 ℃ and hold time is 80 min. With increasing heat treatment temperature, the FT-IR absorption bands appear obvious split, the aluminum-oxide polyhedron in the glass network changes from [AlO4] to [AlO6]. The titanium ion in the glass network gradually transforms to the 6-coordinated, moreover forms minicrystal of MgTi2O5 and Fe2TiO4 which provides the position of heterogeneous nucleation for the growth of crystal.

结果表明:在一定的热处理条件下可以以基础玻璃制备出主晶相为钙铁透辉石,次晶相为钙长石的纤维状结构的微晶玻璃;最佳的热处理工艺为:850 ℃核化100 min,980 ℃晶化80 min;随着热处理温度的升高,红外吸收带发生明显的分裂;玻璃结构中的[AlO4]向[AlO6]转化;网络结构中的钛离子逐渐转变为六配位,形成微晶相——钛酸镁和钛铁晶石,为晶体的生长提供非均匀形核位置。

Thermal models of parallel moving heat source, oblique moving heat source, and circle arc moving heat source are set up and analyzed.

采用均布热源建立平面移动热源模型、倾斜运动热源模型和弧形热源模型,并进行了分析。

In the light of cost index and pollution degree, the characteristics of kinds of pulp are analyzed in detail, and the GP pulp which is low cost, high-yield, no-pollution is chosen as the material of tableware. Based on material element analyzed, shaping technology is designed, the to and for single plane shaping equipment which is high shaping quality, high production efficiency and is easy to automatize is chosen. All kinds of measure are taken to solve the problems which are inequality in the shaping process of GP pulp, and dosage which matches with GP pulp is chosen. Some ways of fixing shape and heat up are analyzed, the technology of saving energy of heat pressing to fix shape being composed of oil heat and only one fixed shape in the mold is applied, with which it is high production efficiency, low cost to fix shape effectively, which saves energy 30 percent. In order to make the production line meet with material of GP pulp, measure are taken to solve the problem of pulp adhered to netlike molding which can lead to carry material difficult, the structure of fully automatic equipment is renovated, the loaded beam is optimizationally designed to make equipment structure compactand improve location precision and products quality. According to technologic flow and actual characteristic, Omron PLC is chosen as the core of the control system, proximity switch as detect unit take the place of touch switch, software is designed reasonably according to time order figure, hardware is simplified, the reliability of system is advanced, the stability of system is assured to make production order. Intelligence neuron PID system is studied theoretically which is made up of both neuron with self-organizing and self-learning function and ordinary PID with the characteristic of the simple structure and high stability, which can automatically tune the parameter with the change of system parameter, remain perfect performance.

按成本指标和污染程度分析各浆料的特点,选择低成本、高得率、无污染的磨石机械浆为原料,在原料组分分析的基础上,设计成型工艺,选择成型质量好、生产率高、易实现自动化的往复式单板成型机,采取各种措施解决GP浆成型不均匀的问题及选择与机械浆相匹配的助剂;分析几种定型方式和加热方式,采用定型效果好、生产率高、成本低的油加热与模内一次性定型相结合的热压定型节能技术,节能30%;为了使生产线适应磨石机械浆原料,采取相应措施解决由于粘网造成物料转移困难,对全自动设备结构进行改进设计,着重对物料传送系统的关键部件——承载梁的进行优化设计,使设备更加紧凑合理,提高设备的定位精度和产品质量;根据生产线工艺流程和现场特点,选用OMRON CPM1A型PLC为主核心,接近开关作为检测元件,替代有触点开关,选用可编程终端代替常规面板按扭,并按照时序图科学合理地设计软件,有效地简化系统硬件构成,提高系统的可靠性,保证系统的稳定性,从而使生产更加通畅有序;从理论上探索将神经元应具有的自组织、自学习要求与PID控制结构简单、稳定性好的全自动纸浆模塑餐具生产线的研究特点结合起来,构成神经元自适应PID控制器,当参数的变化时,系统能自行参数整定,保持优良的工作性能指标,满足实际需求。

The effect of heat source location on the heat transfer of an axially grooved heat pipe was investigated.

探讨了轴向槽道热管垂直安装时热源位置的不同对热管工作特性的影响。

If the heat exchangers are well designed and can supply the heat flux needed for convective heat transfer, then the engine will produce power in proportion to the mean pressure, as predicted by the West number, and Beale number.

改变气体温度会引起相应的变化,气体压力,而运动的活塞造成的天然气将轮流扩大和压缩。气体的行为如下描述了天然气的法律,说明气体的压力,温度和体积是有关系的。

The measuring unit includes one heat block, one cooling block, and one sleeve. The facing end of the heat block and cooling block has one loaded plane which forms one loaded cavity with the sleeve in which the heat block and cooling block can be relative move.

所述量测部包括一加热块、一冷却块及一套筒,所述加热块及冷却块相面对的一端分别具有一承载平面,所述承载平面与所述套筒构成一承载腔,且所述加热块与冷却块可于所述套筒内相对移动。

The influence of those main design parameterssuch as evaporation saturation temperature t_s、heat dissipated power Q and charge ofworking fluid L on the temperature distribution of evaporation"s bottom and boiling heat transfer inside the evaporation has been calculated and analyzed concretely. The method that uses channels to enhance boiling heat transfer of evaporation"s bottom has also been analyzed and calculated preliminarily.

具体计算和分析了蒸发饱和温度t_s、散热功率Q和充液量L等主要设计参数对蒸发段底面温度分布和蒸发段内部沸腾传热特性的影响,对用槽道强化蒸发段底面沸腾换热也做了初步的数值计算和分析。

Based on detailedly analyzing the application and development of plastic heat exchangers at home and abroad, one approach was advanced that by substituting plastic heat exchanger made of thin wall and canaliculus PTFE plastic tube for the metal heat exchanger of traditional lithium bromide absorption cooler.

本文在对国内外塑料换热器的应用、发展进行详尽分析的基础上,提出采用薄壁小管径聚四氟乙烯塑料管制成的塑料换热器代替传统的溴化锂吸收式制冷机中的金属换热器,制作一台塑料管溴化锂吸收式制冷机及其实验系统的课题。

The Φ(subscript PSⅡ), Fv/Fm and qP were increased but qN was decreased with increasing of chlorophyll a, the rate of heat dissipation was increased with the increasing of chlorophyll b, and the carotinoid increasing enhanced the rate of heat dissipation of dryland and carbon assimilation of irrigated cultivar The Φ(subscript PSⅡ) and qN of dryland cultivar treated by control were higher than that of irrigated cultivar in jointing stage significant, indicating that the characteristics of drought-resistantce of winter wheat could be displayed in the jointing stage, and the drought-resistant capability could be increased by enhancing the practical photochemistry efficiency and heat dissipation in jointing stage.

拔节期对照处理的旱地品种的Φ和qN显著高于水地品种,在该时期品种抗旱性差异表现较为明显,能够通过提高光合机构实际光化学效率和热耗散来增强光合机构对干旱的适应能力。

In order to meet the requirement of the Collector ring dipole superconducting magnet of FAIR in the process of operation, meanwhile, and to ensure the heat loads coming from the support structures to be lower than the design demands, the 3D models of support structures have been constructed with CATIA, then the calculation of low-temperature heat-load and the structure analysis have been done with ANSYS, the support structure material, 316LN+G10, is decided according to the heat-load calculation and the structure optimization, these results are necessary for manufacturing the formal magnet.

为保证FAIR收集环(Collector ring-CR)超导二极磁体工作过程中的磁场位形符合设计要求,同时保证由磁体支撑带来的热负荷小于设计要求,用CATIA软件建立了不同结构的磁体支撑3D模型,并用ANSYS有限元分析软件对建立的模型进行了低温热负荷分析和结构分析。通过比较分析的结果和对磁体支撑结构进行的进一步优化,确定了316LN+G10材料的支撑结构,为收集环超导二极磁体工程制造提供了参考。

第18/100页 首页 < ... 14 15 16 17 18 19 20 21 22 ... > 尾页
相关中文对照歌词
Heat Of The Night
The Heat Is On
Children In Heat
The Heat Is On
Turning Up The Heat
The Heat (Outro)
The Heat
Heat Of The Night
Heat Of The Moment
The Heat Goes On
推荐网络例句

Do you know, i need you to come back

你知道吗,我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书,王祥生,李德昌。安徽省首次发现嗜群血蜱。

Chapter Three: Type classification of DE structure in Sino-Tibetan languages.

第三章汉藏语&的&字结构的类型划分。