英语人>网络例句>heat additive 相关的网络例句
heat additive相关的网络例句

查询词典 heat additive

与 heat additive 相关的网络例句 [注:此内容来源于网络,仅供参考]

Based on a computing model of floor heating residences, indoor thermal environment and heat distribution under the effect of heat charge/discharge, operation control and solar radiation has been concluded. Concept and formula of equivalent heat supply has been put forward which indicate that actual heat supply will be equal to the sum of design heat supply and equivalent heat supply. Recommend coefficient has been given taken Dalian as an example. Computed according to the new method, design heat supply can be reduced to 37% in cloudy day and 43.3% in sunny day, energy saving effect is very obvious. In Tromb wall solar house, effect of concrete wall on indoor temperature swing and attenuation of temperature wave is very obvious. While the outdoor air-temperature swing exceeds 10℃, indoor air-temperature swing belows 3℃. In the experiment, maximal difference in temperature between inner surface and outer surface of the 300mm wall exceeded 10℃. Heat storage and collector efficiency varies adversely according to solar radiation. Factors such as thickness, material, absorptance of the wall and permeation of the glass cover all have big influence on heat storage and collector efficiency. There exsisted an optimal thickness of the wall, which can make the best of heat storage and collector efficiency. Most of the heat stored in conventional Trombe wall during the daytime has been lost to the outside at night without heat preservation. Heat preservation on the outside surface of the wall has effectively improved heat release performance of the wall at night, heat supply to the room has increased too.

通过建立的地板采暖系统动态热性能分析模型,得出了在蓄放热特性、运行方式和太阳辐射等因素耦合作用下的室内热环境及热量分配比例,提出了等效供热量的概念及计算公式,指出实际所需供热量应等于设计供热量加上等效供热量,并以大连为例,给出了等效供热量的修正系数,以新方法计算,阴天可减少设计供热量37%,晴天最大可以减少设计供热量43.3%,节能效果显著;集热蓄热墙式太阳房中,混凝土蓄热墙的室温均一化效果和对温度波的削减作用非常明显,当室外温度波动最大幅度超过10℃时,室温波幅不超过3℃,实验中300mm厚墙体内外表面温差超过10℃;墙体蓄热效率与集热效率随太阳辐射照度的变化呈相反的变化趋势;墙体厚度、材料、表面吸收率以及盖板透过率等因素对集热和蓄热效率均有较大的影响,存在一个最佳的墙体厚度值,使得墙体集热和蓄热综合性能最优;传统的蓄热墙夜间没有外保温,辐射散热损失很大,研究表明墙体外保温方式明显改善了蓄热墙夜间的散热性能,增加了向室内的供热量。

The method of CFD numerical simulation is employed to replace experimental investigation. Hence, STAR-CD of the commercial software is used to simulate the outer flow field and heat transfer performance of integrated heat sink with heat pipes cooled by airflow. It is found that simulated results agree with experimental results well, which indicates that simulation method is reasonable and reliable. Further, simulated computations for different fin thickness, fin pitches and air velocities are performed to analyze their effects on heat transfer performance of heat sink. Finally, a new optimized structure of integrated heat sink with heat pipes is provided to meet future demands for cooling CPU and its heat transfer is also evaluated. For multi-heat source and higher dissipation power of electronic devices, the integrated heat sink with heat pipes attatched fins stagged in different positions of channels is presented and its flow and temperature fields are also simulated to enhance heat transfer. As a conclusion, all mentioned above are useful for the design of heat sink with excellent efficiency of heat dissipation and further research.

应用商业软件Star-CD对CPU集成热管散热器的外部流场和传热特性进行了数值模拟,将数值模拟结果和试验结果对比,验证了所提出的数值计算方法是可靠和可行的;利用此数值模拟方法对CPU集成热管散热器在不同散热翅片间距、厚度和气流速度下散热器的流动与传热性能进行了数值计算,分析了这些参数的变化对散热器传热性能的影响;针对未来CPU冷却的要求,确定了与最优气体流速匹配的最佳翅片间距、厚度的CPU集成热管散热器的新结构;利用试验评测了根据数值模拟提供的新结构开发出的新CPU集成热管散热器的传热性能;最后在场协同强化传热的理论的基础上,对CPU集成热管散热器的散热翅片错位排列来强化散热器的散热,满足未来大功率、多热源的电子元件的散热,为今后进一步优化散热器提供了依据。

The research result shows that the flowability, moldability, cohesiveness of high performance concrete of hill sand are significant by comparison with ordinary concrete on mechanical properties, long term properties, and durability. Motar flowability decreases with the increase of single-mixed active additive. The flowability can be largely improved by double mixing of active additive and super plasticizer NF. This is because not only the active additive has filling effect but also the dispersing effect induced by surface action between additive and super plasticizer NF. And the optimal content of materials are: super plasticizer NF≥0.8%, fly ash 20%, PS 20~30%,zeolite powder≤20%,SF 5~8%; The negative influence of hill sand powder should be avoided by controlling of powder content and the use of active additive and super

研究表明:随着单掺活性掺合料掺量的增加,砂浆流动性减小,活性掺合料与萘系高效减水剂NF双掺使用,比使用同样剂量萘系高效减水剂NF的基准浆体流动性明显增大,这是由于玻璃体材质活性掺合料不仅有填充效应,更主要的是它与高效减水剂之间的表面物化作用产生了分散性,而活性掺合料对浆体的流化作用效果主要是依赖于其分散性;能有效改善胶砂流动性的适宜掺量为:萘系高效减水剂不小于0.8%,粉煤灰掺量为20%,PS掺量为20~30%,沸石矿粉掺量不宜大于20%,SF掺量为5~8%;通过对粉末含量的限制,并借助活性掺合料、高效减水剂的合理使用,就可以避免山砂粉末含量的负面影响,配制出密实度高,抗渗性能优异,具有良好的耐久性能,并具有良好的体积稳定性的山砂高性能混凝土。

Monte Carlo simulations were conducted to study the new approaches of QTL mapping, the results indicated that general least squares method, which was widely applied in mixed linear model, could unbiasedly estimate all genetic main effects, including additive effects, dominance effects and epistatic effects of additive by additive, additive by dominance, dominance by additive, dominance by dominance.

对新提出的QTL分析力法进行了Monte Carlo模拟研究,结果表明,广泛应用于混合线性模型的广义最小二乘法能够无偏估计加性效应,显性效应以及加加、加显、显加、显显上位性效应等各项遗传主效应;运用线性无偏预测法能够无偏预测上述各项遗传主效应与环境的互作效应;基于QTL效应的杂种优势预测也是无偏的。

Water inside vacuum heat- collection tubes; since the hot medium inside vacuum tubes floats up and cold one goes down due to respective specific gravity, hot and cold mediums convections up and down to cause the heat conduction, furthermore transfer the heat to the related working medium in the heat tubes, the working medium sorbs the potential heat and becomes steam to rise up to the condensing section from the tube heat evaporating section; it emits the heat in condensing section to change again into liquid working medium; it flows back to evaporating section under the gravity action, the emitted heat is transferred into the water inside water tank or tube group by means of the heat-conduction through heat tubes condensing section; it makes the cold water in water tank into hot water in the repeated way.

阳光透过全玻璃真空集热管的外玻璃,照射到涂覆在内玻璃管外表面的选择性吸收涂层上,涂层将太阳的辐射能吸收并转化为热能,通过内玻璃管壁导热,传递给真空集热管内其液态传热介质,由于真空集热管内热的介质因比重小而上浮,冷的介质因比重大而下沉,冷热介质上下对流传热和导热,再通过热管的金属壁导热,将热量传递给热管内其相变工质,工质吸收汽化潜热而变成蒸汽,由热管蒸发段上升到冷凝段,在冷凝段放热冷凝,又变成液态工质,在重力作用下流回蒸发段,所放出的热量通过热管冷凝段金属管壁导热,传递给水箱或联集管内的冷水,周而复始,于是便将水箱内的冷水全部加热成热水。

First is enhances the boiler the heat energy transfer rate,(1) changes the vertical chimney to the horizontal-type chimney, reduces the speed of flow, Increase the time which the actuating medium and the boiler hot flame doing heat change;(2) changes the high temperature system sole medium sole heat transfer area to many kinds of medium the multi-channel heat transfer area(2-6 medium, 2-6 heat transfer area, this article takes four medium, 4 heat transfer areas confer elaboration), the increase heat transfer flow path through many times heat absorption,Lets the pot furnace coal flame heat energy as far as possible much transmit gives the actuating medium, Enables the quantity transfer rate from the present 60%--75% enhances to is bigger than 95

第一是提高锅炉的热能转移率,(1)将立式烟囱改为卧式烟囱,降低流速,增加工作介质与锅炉热焰气的热交换时间;(2)将高温系统单一介质的单一换热区改为多种介质的多道换热区(2—6种介质, 2—6道换热区,本文取四种介质,4道换热区加予论述),增加换热流程,通过多次吸热,让工作介质尽可能多地把锅炉煤焰气的热能传递给工作介质,使能量转移率从现在的60%--75%提高到大于95

--- Method and apparatus for abstracting water from air wherein in a first phase of a recurring cycle a stream of cool, moist air from the atmosphere first cools a first heat storage condenser (1) and then humidifies a hygroscopic medium (14); in a second phase a stream of warm air additionally heated by solar radiation expels moisture from the hygroscopic medium and carries the moisture into said first heat storage condenser (1) where it condenses, releasing condensation heat, and drains away; in a third phase another stream of cool, moist air from the atmosphere first cools a second heat storage condenser (2) and then rehumidifies the hygroscopic medium, and in a fourth phase another stream of warm air heated by solar energy again expels the moisture from the hygroscopic medium and carries the moisture to said second heat storage condenser where it condenses and drains away, and wherein the warm air streams of the second and fourth phases, are preheated using the heat of condensation picked up by the said second heat storage condenser (2) in the fourth phase and the heat of condensation picked up by said first heat storage condenser (1) in the second phase, respectively, before being additionally heated by solar radiation and being used to expel moisture from the hygroscopic medium.

摘要---方法和仪器取水,从空气,其中在第一阶段的周期性循环流冷静,潮湿空气从大气中的第一冷却的第一个蓄热冷凝器( 1 ),然后humidifies一吸湿中等( 14 );在第二阶段流的暖空气此外,激烈的太阳辐射驱逐水分从吸湿中等,并进行水分成表示,第一蓄热冷凝器( 1 )凡它凝结,释放出凝结换热,及雨水渠的距离;在第三阶段另一流的冷静,潮湿空气从大气中冷却,第一第二蓄热冷凝器( 2 ),然后rehumidifies该吸湿中等,而在第四个阶段的另一流的暖空气加热太阳能再次驱逐水分从中期和吸湿性带有水分说,第二蓄热冷凝器而凝结及排水渠远离,和其中的暖空气流,第二和第四阶段,预热用热凝结回升,由说,第二蓄热冷凝器( 2 )在第四个阶段和热凝结回升,由说,第一蓄热冷凝器( 1 )在第二个阶段,分别之前,此外激烈的太阳辐射和被用来驱逐水分从吸湿中等。

In order to make the right evaluation of the state which is the consumption consume of the steam line system, we make an test of the heat loss of the steam line network. And we also probe into the heat loss of the steam line system and the factors. In order to solve the heat inefficency of the steam line system, we look into the present situation of the steam line network and the state of heat preservation. Then we found the open questions and the weak points of heat preservation. We make the evaluation and affirm the reason of the heat inefficency of the system. We adopted the combination of bench test and engineering optimization, then we screened out high-quality adiabator, and designed the best heating composition. We designed and developed the software"The analysis and optimization of energy of the steam line system in thermal production" It can offer convenience to the computational analysis of heat loss of the steam line system. It can also be used for design calculation and experimental verification of steam pipeline feasible radial-radius, so it can offer technical support for the reduce of heat loss of the system, the raise of well head steam quality and the raise of heat efficicency of the steam injection system.

为了对输汽系统的用能状况作出正确的分析评价,对输汽管线热损失进行了测试计算,对输汽系统热量损失及影响因素进行了探讨;为了解决输汽系统热效率低的问题,从输汽管网现状及管道保温状况调查入手,掌握存在的问题和保温薄弱环节,做出分析评价,确认导致系统热效率低的原因,采用室内试验与工程优化相结合的办法,筛选出优质保温材料,设计最优保温结构,同时设计开发了&热采输汽系统能量分析及优化软件&,为输汽系统热量损失计算分析和保温结构优化提供了方便,还对输汽管线合理辐射半径进行了设计计算及实验验证,从而为降低系统的热能损失,提高井口蒸汽干度,提高注汽系统的热效率提供了技术支持。

052 Describes and claims a body of polycrystalline dielectric ceramic material having a lead zirconate--lead titanate--lead stannate composition falling within the area A B C E F of the triaxial diagram 1d of the drawings accompanying this specification and containing at least one substitutional additive ingredient selected from the group consisting of elements having respective ionic radii sufficiently close to the ionic radius of one of the elements lead, tin, titanium, zirconium and oxygen to permit of substitution, and a valence state differing from that of said one element by less than three units, the aggregate quantity of additive ingredient amounting to from 0.1 to 5 percent of the replaced ion on an atom basis, each additive ingredient present in said material being in ionic form and substituting for a finite percentage of the ions of a particular one of the elements lead, tin, titanium, zirconium and oxygen with respect to which it conforms with regard to ionic radius and valence state, said additive ingredient replacing a quantity of said elements having in the aggregate an equal number of valence units.

参考译文:第 1012052 号专利说明书介绍一种含有锆酸铅,钛酸铅,锡酸铅的多晶陶瓷介质材料,其组成在说明书附图 ld 三元相图中处于 A B C E F 区域内,该组成至少还含有一种置换添加物,这种添加物从一组离子半径分别接近于铅,锡,钛,锆,氧的元素中选出,以利于互相置换,而与上述一种元素化合价之差应小于三价。该添加物的总量为被置换离子的 0.1%~5%克原子。上述材料中的每种添加物是以离子形式存在的,它以一定的百分数置换铅,锡,钛,锆,氧中的某一元素的离子。添加物在离子半径和价数上必须类似于上述任一元素,并且置换添加物的量与被置换的元素在总体上具有相等的化合价数。本句由两个简单句构成,一个主句,另一个是定语从句。

This method can analyze diesel oil additive whose efficacy is unknown. It only takes some simple physical property tests of the diesel oil samples added unevaluated diesel oil additive or a kind of known better diesel oil additive to do the grey relation analysis and evaluate the unevaluated additive.

应用这个方法分析待测功效的柴油添加剂,可通过测定加入它后的柴油样品的物理性质和加入已知功效较好的柴油添加剂的柴油样品的物理性质,再作灰色关联分析,综合关联顺序以评定其功效好坏。

第1/500页 1 2 3 4 5 6 7 8 9 ... > 尾页
相关中文对照歌词
Certified
The Heat
Take The Heat Off Me
Born Under Punches
Like A Candle
The Heat Is On
Heat Of The Night
The Heat Is On
Go Slow
Heat Of The Night
推荐网络例句

The network space is the typical form of abstract space when it comes to the digital stage.

网络空间是抽象空间数字化阶段的典型形式。

The Notarial System,as the system of judicial certification in our country,is both the constructor and the defender of social credit system,It has its special value and function in the social honesty.

公证制度作为我国司法证明制度,既是社会信用体系的建设者,同时也是社会信用的捍卫者,在诚信中有其特殊的价值和功能。

"He'll never love you as much as you love him," Ben pronounced.

"他永远不会像你爱他那样爱你。"本说。