查询词典 hardness

The hardness and wear resistance increase with increasing TiB2 content. Adding about 1.5%Mg in melt restrains the conglobation of the TiB2 particles, which makes the size of TiB2 particle decrease and the distribution of TiB2 particle is more homogeneous. The strengthening effect of TiB2 particles is enhanced and the hardness and wear resistance of composites are obviously improved. The excess Mg decreases the refinement effect of TiB2 particles, but the hardness and wear resistance are improved continuously.

结果表明：反应生成的TiB2颗粒平均尺寸约为0.5 μm，材料的硬度和耐磨性随着TiB2含量的增加而提高；添加1.5%Mg元素可明显细化TiB2颗粒，且使其分布更加均匀，增强TiB2颗粒的弥散强化和细晶强化效果，复合材料的硬度和耐磨性显著改善；过量的Mg元素(3%)会造成TiB2颗粒细化效果的下降，但其硬度和耐磨性能继续得到改善。

The company's main products: color detection instruments: Glossiness Miriam, Miriam color spectrophotometry, standard light source for color light box, transmissioní°Miriam, Miriam orange peel, fresh young tester; surface coating physical properties testing instruments: Coating thickness, wet film thickness, temperature tracker, surface humidity instrument, dewpoint meter, roughness instrument, electric spark pinhole leak detectors; Detect mechanical properties of surface coating equipment: zoned grid, and pencil hardness tester , impact tester, hardness testing sticks, Latvia Law / hydraulic adhesion tester, abrasion tester, cylinder / cone bending tester, cups sudden device, surface tension instruments, scratch pen, indentation hardness tester, etc.; paint coating equipment dedicated category: fineness board, drying time recorder, wet adhesion tester, paint ohmmeter, PH, the coating device, mixer, bead mill, mixer, spray gun, putty detector Miriam, white tester, iron cobalt colorimeter, moisture titrator; viscosity-type equipment: Viscosity Cup, density cup, bubble viscosity tube viscometer, infiltration cup rheometer, viscosity units conversion meter; laboratory standard consumables: Mitsubishi pencil tests, 3M adhesive tape test, RCA tape, rubber, the hiding power test paper for color tubes, microscopes dedicated LED ring light source, transfer ink knife and ink scraper, brush, Color Card, gray cards, zirconia beads, glass beads, pieces of cement mortar, the standard of fly ash, the standard viscosity fluid, stopwatch, chemical industry-standard compilation of manuals, paint paint testing manual; test standard Material: tin plate, steel plate, aluminum sheet, asbestos-cement pressure plate, Eterpan, glass, maple panels, MDF, copper film, polyester film, copper; measuring meter and optical instruments: digital calipers, micrometer, dial gauge a high scale, depth gauge, thickness gauge, diameter gauge, gauge block, magnifiers, microscopes, projectors, video measuring instrument; environmental test equipment: oven, constant temperature and humidity box, hot and cold circulating water bath, salt spray test chamber, high temperature resistance furnace, fluorescent UV aging chamber, xenon lamp aging chamber; electronics equipment: infrared thermometer, multimeter, clamp sheet, thermal imager, temperature and humidity meter; anti-static instruments: static tester, surface resistivity device, flat-panel monitor, anti-static footwear tester, wrist strap tester, body Tester; other types of instruments and equipment: torque tester, temperature and humidity recorder, push pull, the vibrometer, speed instrument, analytical balance, industrial Scale Units, dust particle counter, X-ray fluorescence coating thickness measurement and elemental composition analyzer, and so on.

公司主营产品：外观颜色检测仪器：光泽度仪、分光色差仪、标准光源对色灯箱、透射雾影仪、桔皮仪、鲜映性测试仪；表面涂层物理性能检测仪器：涂层测厚仪、湿膜测厚仪、炉温跟踪仪、表面湿度仪、露点仪、粗糙度仪、电火花针孔检漏仪；表面涂层机械性能检测仪器设备：划格器、铅笔硬度计、冲击试验仪、硬度试验棒、拉脱法/液压式附着力试验仪、耐磨耗试验机、圆柱/圆锥弯曲试验仪、杯突仪、表面张力仪、划痕笔、压痕硬度计等；涂料油漆类专用仪器设备：细度板、干燥时间记录仪、湿附着力耐擦洗试验仪、油漆电阻计、PH计、涂膜器、混合机、珠磨机、搅拌机、喷枪、腻子测定仪仪、白度仪、铁钴比色计、水份滴定仪；粘度类仪器设备：粘度杯、密度杯、气泡粘度管、粘度计、渗透杯、流变仪、粘度单位换算计；实验室标准消耗品：三菱测试铅笔、3M测试胶带、RCA纸带、橡皮条、遮盖力测试纸、对色灯管、显微镜专用LED环型光源、调墨刀、墨铲、狼毫刷、色卡、灰卡、锆珠、玻璃珠、水泥砂浆块、标准粉煤灰、标准粘度液、秒表、化学工业标准汇编手册、涂料油漆测试手册；测试级标准基材：马口铁板、钢板、铝板、石棉水泥加压板、埃特板、玻璃板、枫木面板、中纤板、紫铜片、聚酯膜、铜棒；量具量仪及光学仪器：数显卡尺、千分尺、千分表、高度尺、深度规、厚度规、内径规、量块、放大镜、显微镜、投影仪、影像测量仪；环境测试设备：烘箱、恒温恒湿箱、冷热循环水浴、盐雾试验箱、高温电阻炉、荧光紫外老化试验箱、氙灯老化试验箱；电子类仪器：红外测温仪、万用表、钳形表、热像仪、温湿度仪；防静电仪器：静电测试仪、表面电阻仪、平板监测仪、防静电鞋袜测试仪、手腕带测试仪、人体综合测试仪；其他类仪器设备：扭力测试仪、温湿度记录仪、推拉力计、测振仪、转速仪、分析天平、工业台秤、尘埃粒子计数器、 X-射线荧光涂层测厚和元素成分构成分析仪，等等。

With the surface hardness is required, and in determining the purchase and business operators after properly can be broken hacksaw oral zoned, zoned when if skid No traces of high hardness, zoned shallow marks after the hardness has a higher designated a distinct traces of low hardness.

与表面硬度是必需的，在决定购买和经营者正确后可以被钢锯口头划，划打滑时，如果没有高硬度的痕迹，后划为浅标志硬度有较高的指定低硬度明显的痕迹。

The experiment study about the subcritical normalizing holding temperature effects the macrostructure and hardness of the 40SiMnCrNiMoA steel shows: When subcritical normalizing holding temperature is 760℃, the ferrite in the mixture phase structure is lumpish, the hardness of the steel is low (about HRC32), and when the holding temperature is over 800℃, the hardness of the steel is about HRC49, the ferrite in the mixture phase structure is in old critical range austenite grain boundaries, it is disadvantage for the steel strengthening. When the holding temperature is 780℃, the mixture phase structure is mixture phase structure including the strip ferrite、martensite and bainite, the ferrite is less than 20%wt, its grains are fine and even, the hardness of the steel is about HRC38, it is in the range of HRC35-40 which is the long-life drill rod needed.

亚温正火温度对40SiMnCrNiMoA的组织和硬度等性能的影响的实验研究表明，当亚温正火保温温度为760℃时，复合组织中的铁素体形态是块状，处理后的材料硬度相对较低（HRC32左右）；而当采用大于800℃温度亚温正火处理，材料硬度为HRC49左右，组织中铁素体大部分较连续地存在于原奥氏体的晶界，对材料强化不利；当40SiMnCrNiMoA钢780℃亚温正火后，硬度为HRC38左右，在以往小钎杆较长寿命所需硬度范围HRC35-40内，而组织为细条状铁素体+以板条马氏体和条状无碳贝氏体为主的复合组织，晶粒细小均匀，铁素体体积含量少于20％。

This paper has obtained following three results about the new scheme:(1) The hardness of recovering the private key from the public key is based on the hardness of the shortest vector problems of several lattices;(2) The hardness of forging a signature is equivalent to the hardness of the closest vector problem of some lattice;(3) Each signature will leak information on the private key,but the final shape of the unlimited leakage is just a group of complicated non-linear equations.

文中给出新方案的3个结果：(1)由公钥恢复出私钥的困难性基于若干格上的最小向量问题；(2)由公钥伪造签名的困难性等价于某个格上的最近向量问题；(3)每个签名值仍然会泄露私钥的一些信息，但无限制泄露的最终形式只是关于私钥的一组复杂的非线性方程。

Contrapose the all of contradiction brought by increasing hardness of silicone rubber base on affecting mechanism of all factors, resolved the confliction brought out by hardness and strength, hardness and elasticity, hardness and thermal stability.

并通过研究各种因素对高硬度硅橡胶性能影响的机理，解决了硅橡胶因硬度增加而引起的强度、回弹性和耐热性等性能严重劣化的问题。

Contrapose the all of contradiction brought by increasing hardness of silicone rubber base on affecting mechanism of all factors, resolved the confliction brought out by hardness and strength, hardness and elasticity, hardness and thermal stability.

分析了两种填料对硅橡胶性能的影响，着重研究了高硬度硅橡胶的热稳定性。并通过研究各种因素对高硬度硅橡胶性能影响的机理，解决了硅橡胶因硬度增加而引起的强度、回弹性和耐热性等性能严重劣化的问题。

Silica and alumina, to an organic silicone rubber, ShoreA 70, to improve the hardness of silicone rubber material and the results indicated that the addition of silica improved the hardness of the material dramatically, but depressed the heat-resistance markedly; the addition of alumina improved the hardness of the material also, but more loading was needed to achieved the hardness as compared with the silica added materials.

研究发现，添加气相法白碳黑能显著提高硅橡胶的硬度，但使硅橡胶的耐热老化性能明显变差；氧化铝也可以用于提高硅橡胶的硬度，但与气相法白碳黑相比，达到相同硬度时的添加量要大的多；比较而言，通过添加氧化铝获得的高硬度硅橡胶具有较好的综合性能，更能满足电化铝烫印版的制作需要。

In this paper,the correlativity between the Brinell hardness and the Rockwell hardness has been investigated by regression analysis,the regression equation between the Brined hardness and the Rockwell hardness is obtained,therefore the quantitative analysis can be carried out.

本文根据布氏硬度与洛氏硬度之间的相关关系，采用数学回归分析方法，求出它们之间的数学表达式──数学回归直线方程，从而能定量地阐述两者之间的关系

This welding wire not only has the inherent properties of metal powder-cored wire, such as with better welding quality, without slag, highly efficiency and conveniently adjusting the alloying elements etc., but also has the advantage of low hardness in as-welded (less than HRC45), good machinability, high hardness in as-aged (more than HRC55) and better wear resistance with customary working procedure on making or repairing equipments such as rollers when reasonable designing the alloys content. The author adequately makes use of the high-tempering in the required stress relieving working procedure. During this working procedure, which causes the hardness of overlaying metal increased by the reason of austenite changes into tempered martensite and more chiefly what is the precipitation of a lot of carbide by secondary hardening simultaneously. This wire can solve the hard rolled problems of some solid wires with higher alloys while it can get over the conflict of existing overlaying materials what are always possesed high hardness with poor machinability or low hardness, good machinability with poor wear resistance. Further, it also can overcome the intenerating phenomena between welding beads and make the external hardness of overlaying metal uniform. Be sure it could be found important meaning in the overlaying of wear-resistant equipments, such as the precise roller.

该焊丝除了具有金属粉型药芯焊丝焊接质量好、无渣、高效率和合金成分可方便调节等固有的优点外，合理的设计粉芯中的合金成分，按通常工序制造与修复轧辊等设备，充分利用必需的消除应力工序的高温回火，堆焊层金属在奥氏体转变为回火马氏体的同时更主要是通过二次硬化析出了大量碳化物导致硬度增加，使得该焊丝还具有焊态硬度低(小于HRC45)、机加工性能好和时效态硬度高(大于HRC55)、耐磨性能好等优点，解决了某些高合金实芯焊丝轧制困难的问题，同时克服了现行堆焊材料硬度高、加工性能差或者硬度低、加工性能好、耐磨性差的矛盾，并能克服焊道之间的软化现象，使堆焊表面硬度较为均匀，对耐磨件，譬如精轧辊的堆焊具有重要意义。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。