查询词典 hardening

A hardening and tapering of the udder tissue can be detected at the point of connection with the belly at 24 hours post farrowing.

小猪出生后24小时，在与腹部相连的地方，乳头将会出现滴奶和乳头变小。

As strain-hardening effect greatened on the load-bearing polyethylene, the release of plate-like wear debris augmented and caused upward increase in an added sequence.

由两产品的测试结果比较： B 型产品磨损较多，所以释出的磨耗屑重量也明显多於 A 型产品。

The effect of fly ash during the hydrating and hardening process of composite binder was studied.

分析了粉煤灰在复合胶凝材料水化硬化过程中的作用。

Malcacia: intenerated and hardening on the contrary, is when the device is vibration or high temperature, component or device of strength than the normal state to a phenomenon.

强硬：与强硬相不正，强硬是当摆撤在施到颠簸或矮温的环境后，元件或摆撤体的强度比变态状况给弱的一种本体。

This welding wire not only has the inherent properties of metal powder-cored wire, such as with better welding quality, without slag, highly efficiency and conveniently adjusting the alloying elements etc., but also has the advantage of low hardness in as-welded (less than HRC45), good machinability, high hardness in as-aged (more than HRC55) and better wear resistance with customary working procedure on making or repairing equipments such as rollers when reasonable designing the alloys content. The author adequately makes use of the high-tempering in the required stress relieving working procedure. During this working procedure, which causes the hardness of overlaying metal increased by the reason of austenite changes into tempered martensite and more chiefly what is the precipitation of a lot of carbide by secondary hardening simultaneously. This wire can solve the hard rolled problems of some solid wires with higher alloys while it can get over the conflict of existing overlaying materials what are always possesed high hardness with poor machinability or low hardness, good machinability with poor wear resistance. Further, it also can overcome the intenerating phenomena between welding beads and make the external hardness of overlaying metal uniform. Be sure it could be found important meaning in the overlaying of wear-resistant equipments, such as the precise roller.

该焊丝除了具有金属粉型药芯焊丝焊接质量好、无渣、高效率和合金成分可方便调节等固有的优点外，合理的设计粉芯中的合金成分，按通常工序制造与修复轧辊等设备，充分利用必需的消除应力工序的高温回火，堆焊层金属在奥氏体转变为回火马氏体的同时更主要是通过二次硬化析出了大量碳化物导致硬度增加，使得该焊丝还具有焊态硬度低(小于HRC45)、机加工性能好和时效态硬度高(大于HRC55)、耐磨性能好等优点，解决了某些高合金实芯焊丝轧制困难的问题，同时克服了现行堆焊材料硬度高、加工性能差或者硬度低、加工性能好、耐磨性差的矛盾，并能克服焊道之间的软化现象，使堆焊表面硬度较为均匀，对耐磨件，譬如精轧辊的堆焊具有重要意义。

Jails have a way of hardening a person's heart.

监狱可以令人的心变得刚硬。

Not suitable for case hardening or nitrating.

不适合的情况硬化或硝化。

But for the TEC overmatching, the residual stress σ〓 in the weld center is also related with the strain hardening coefficient H W of the weld metal. The residual stress σ〓 in the weld center got to the yield strength σ〓 increases little when the H'w is lower and somewhat exceeds the σ〓 when the H'w is higher.

而高胀匹配时的焊缝中心纵向残余应力σ〓还与焊缝金属应变硬化指数H〓有关，H〓较低时，焊缝中心纵向残余应力σ〓在达到焊缝金属屈服强度σ〓后不再升高；H〓较高时，焊缝中心纵向残余应力σ〓可超过焊缝金属屈服强度σ〓。

They are FF testing methods, surface treatment technique, evaluation of the properties of surface modification layer, coating induced embrittlement, selection of coating materials, effects of SP and other surface modification on fretting fatigue resistance . A new coating technology combined with shot peening is proved in improving FFR of titanium alloy. The relation between fretting wear and fretting fatigue mechanism of titanium alloy are discussed on the basis of the experimental results. The main contributions are as follows:(1) Shot peening is the most efficient way in improving fretting fatigue resistance of titanium alloys. Working hardening, roughening and compressive residual stress are involved in the shot peened surface.

本文针对上述问题，从影响FF行为的关键环节：FF实验方法、表面处理工艺技术及表层性能评价、镀层引起的钛合金脆化行为、脆化机制及镀层材料的选择、喷丸强化因数和表面涂层对钛合金FF抗力的影响、FF与微动磨损的联系等，深入系统地研究影响钛合金FF抗力的控制因数，探讨FF机理，并通过喷丸形变强化与新型表面镀或渗层合理复合，达到进一步提高钛合金FF抗力的目的。

Oxygen is widely applied in the metal ndustries in conjunction with acetylene and other fuel gases for metal cutting, welding, scarfing, hardening, cleaning, and melting.

同乙炔和其它燃料气体一起，氧广泛应用于金属工业的金属切割、焊接、嵌接、淬火、清洁和熔化。

Recall that, in the Kolmogorov axiomatization, measurable sets are the sets which have a probability or, in other words, the sets corresponding to yes/no questions that have a probabilistic answer.

延期开工的Kolmogorov宣布要衡量所有套职能有限许多坐标限制在于衡量子寅。换句话说，如果是/否的问题回答f可看的价值观念在许多最有限坐标，然后它有一个概率的答案。

The experimental results showed that the algorithm can filter singular points and remain fixity of the target edge.

实验表明：基于模糊理论的图像智能滤波方法比常规图像滤波方法运算量小，它既能去除奇异点，又能保持图像中目标的边缘不变性，具有很好的滤波效果。