查询词典 hanger rod

Feed thy people with thy rod, the flock of thine heritage, which dwell solitarily in the wood, in the midst of Carmel: let them feed in Bashan and Gilead, as in the days of old.

7：14 求耶和华在迦密山的树林中，用你的杖牧放你独居的民，就是你产业的羊群。求你容他们在巴珊和基列得食物，像古时一样。

The feed rod, which contains a keyway throughout most of its length, passes through the two reversing bevel pinions and is keyed to them.

光杠上有一个几乎贯穿整个光杠的键槽，光杠通过两个转向相反并用键相连接的锥齿轮传递动力。

It was found that the stability of the melt was seriously affected by the diameter, the density and the homogeneity of the feed rod. The dense and uniform feed rods with pure phase were prepared by complete mixing and repeated sintering at a suitable temperature.

在适当温度下多次预烧结和反复混料，并通过最后的烧结可获得纯相、均匀和致密的原料棒；原料棒直径一般控制在10 mm以内； 3～5 mm/h的生长速度适合晶体生长；生长结束时缓慢降温和退火处理可抑制YFeO3晶体的开裂。

The feed rod, which contains a keyway throughout most of its length, passes throughthe two reversing bevel pinions and is keyed to them.

车削很少在其他种类的机床上进行，因为其他机床都不能像车床那样方便地进行车削加工。

Thus, through this gear train, leading from the spindle to the quick-change gear box, thence to the lead screw and feed rod, and then to the carriage, the cutting tool can be made to move a specific distance, either longitudinally or transversely, for each revolution of the spindle.

叩2到0.118英寸尺寸范围内的48种进给量；而使用丝杠可以车削从1.5到92牙／英寸范围内的48种不同螺纹。

A typical lathe provides, through the feed rod, forty-eight feeds ranging from 0.002 inch to 0.118 inch per revolution of the spindle, and, through tne lead screw, leads for cutting forty-eight different threads from 1.5 to 92 per inch.

一些老式的或价廉的车床为了能够得到所有的进给量和加工出所有螺纹，必须更换主轴和变速齿轮箱之间的齿轮系中的一个或两个齿轮。

A typical lathe provides, through the feed rod, forty-eight feeds ranging from inch to inch per revolution of the spindle, and, through the lead screw, leads for cutting forty eight different threads from 1.5 to 92 per inch.

一台典型的车床的主轴没旋转一圈，通过光杠可以获得从到英寸尺寸范围内的48种进给量；而使用丝杠可以车削从1.5到92牙/英寸范围内的48种不同螺纹。

Thus, through this gear train, leading from the spindle to the quick-change gear box, thence to the lead screw and feed rod, and then to the carriage, the cutting tooling tool can be made to move a specific distance, either longitudinally or transversely, for each revolution of the spindle.

主轴就是这样通过齿轮传动链来驱动变速齿轮箱，再带动丝杠和光杠，然后带动拖板，刀具就可以按主轴的转数纵向的或横向地精确移动。

Accordingly, undertook improvement to measurement technique and unit of feet lens group, rear sight the design is staff guage of 0.02mm mobile vertical for the least scale division value, telescopic design is collimation binoculars, face of lens of feed rod lever is 1.2362m above to rear sight distance.

因此，对测量方法和尺镜组装置进行了改进，将标尺设计为最小分度值为0.02mm移动铅直标尺，望远镜设计为准直望远镜，光杠杆镜面到标尺距离为1.2362m以上。

The apron is transmits the guide screw and the feed rod turns on lathe the transportation to turn becomes the apron the translation and the impetus tool rest enters gives, controls the tool rest movement to put through, the separation and the commutation.

将光杠的运动传至纵向齿轮齿条和横向进给丝杠的传动机构，接通、断开和转换纵横进给的转换机构，保证机床工作安全的过载保险装置，丝杠、光杠互锁机以及控制刀架纵、横向机动进给的操纵机构。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48