查询词典 halfway line

Halfway that cannot be deprived twines me.

中途的那不能够被剥夺搓我。

He then unzipped the bag halfway and opened it just slightly to let me have a peek.

他把包的拉链拉了一半，微微打开让我瞄了一眼。

Its sensors are sensitive enough to detect radioactivity that wafts halfway around the globe.

这些探测器的灵敏度相当高，完全可以探测到随风飘散至世界各地的放射性颗粒。

That was about halfway through, in spite of shortages of men and explosives.

这是约一半，在男人和炸药尽管短缺。

Shen Nong top mist throughout the year the vast, bare rock, there is a long moss and ferns, are located halfway up on the bamboo forest, alpine fir forest and rhododendron forest.

神农顶终年雾霭茫茫，岩石裸露，长有苔藓和蕨类植物，山腰上则分布着箭竹林带、冷杉林带和高山杜鹃林带。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

Jagoda whistles him to a stop halfway down the hill, casts him right with a wave to circumvent a brush pile, then stops him at water's edge to reset the course.

为了让艾维斯找到目标，在它跑到半山坡的时候，贾各达吹着哨，让它停在了溪口附近，重新安排线路。

Place a cake pan, filled halfway with hot water, on the bottom shelf of your oven to moisten the air.

一个蛋糕盘，填补了一半用热水，底部大陆架的烤箱湿润的空气。

We were only halfway across the desert when the gas tank got as dry as a bone.

我们横穿沙漠才走了一半，油箱就干得底朝天了。

He cuts off the tips of his asparagus starter and dips them in the accompanying sauce, which he declares to be halfway between Bearnaise and custard.

他切下开胃菜芦笋的尖，蘸上与之搭配的调味汁，他宣称这种调味汁的味道介于蛋黄酱和奶油蛋羹之间。

These rules reflect some inherent feature of self and nonself, and they are the basic detection criterion of GECISM.

这些规则反映了"自我"和"非我"的内在特征，是GECISM进行"非我"检测的判据。

Until today, the media from China and the outside world still uses the term "Post 89". Regardless to whether it is for commercial gimmick or convenience, everybody still remember "Post 89", a term which carries a strong Cantonese accent.

时至今日，国内外艺术媒体还是在沿用&后八九&这个称谓，不管当初是为了商业噱头还是容易上口好记，反正大家现在是记住了&后八九&这个广东口音很重的词。