查询词典 greater than

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

Nowhere will the challenge be greater than in India, home to that symbol of the country, the royal Bengal tiger .

作为孟加拉虎的故乡，印度所面临的挑战要远远大于其他任何国家。

It"s revealed that the consistency probability of unsigned ones complement addition with bit-wise exclusive-OR is very greater than the ideal value 2~", though it is very small, and the consistency probability of unsigned ones complement addition with addition modulo 2 is 2/3 approximately, hence it is very large.

结论表明，进位返加运算与逐位模2加运算的相容概率尽管很小，但远大于理想值2~；进位返加运算与模2~n加运算的相容概率很大，近似为2／3。

We'll then I'll just take off my hat, comb my blond hair and bow to a team greater than us

如果是Xcn？那我将脱下我的帽子，梳理我这金黄色的头发然后向比我们更强大的队伍深深的鞠躬。

Those provide a practical and valid method for designing a feedforwardpower amplifier. Utilizing these and for TD-SCDMA we research and develop thedivider, coupler, bridge and power amplifier at 2.35GHz. Finally I accomplished asimple and minimal structured feedforward power amplifier. Its measured third-orderintermodulation distortion is -50dBc, which is 40dB greater than there is nolinearization technique.

根据分析结论，针对中国自主开发的TD-SCDMA 标准，设计实现了2.35GHz 的功分器、功率合成器、耦合器以及矢量调制器和功率放大器，最终实现了结构简单、体积小巧的前馈功放系统，完成了对放大器的线性化，三阶交调系数优于-50dBc 比线性化之前三阶交调系数改善了40dB。

At pressures and temperatures greater than the critical point, carbon dioxide exists only as a supercritical fluid.

在压力和温度大于其临界点时，二氧化碳只可能以超临界流体形式存在。

Note that, the choice of resistance must ensure that the necessary conditions of work TL431 is the current through the cathode is greater than 1 mA.

需要注意的是，在选择电阻时必须保证TL431工作的必要条件，就是通过阴极的电流要大于1 mA 。

However, if you have clay soil, it's best to dig to frost depth if greater than 24 in.

然而，如果您有粘土，那是最好的连接深度如果很大地比例在24寸。

Cold-rolled sheet can be used directly in temperatures greater than 250 ℃ forming thermal processing.

冷轧板可直接用于大于250℃温度下的热加工成形。

Furthermore, the thickness of the CsI can be greater than that of a rare earth screen because when CsI is deposited on the array it grows in a columnar structure.

此外，因为碘化铯附着在阵列上形成柱形结构，碘化铯比非植入屏要厚很多。

It seems likely that Kraft will return with a better offer.

看起来卡夫要重新考虑一个更好的出价了。

But he'd rather burn off my feelers and watch me squirm.

可他却放任那个家伙对我为所欲为！