查询词典 granularity

The results show that the optimal parameters of this technique are as time of 3 h, temperature of 150 ℃, ratio of liquor to solid of 1.21, H2SO4 additions of 25%, 85% material granularity of 0.095 mm. The one-step leaching percent of vanadium can reach 77%, the leaching percent obtain 90% after two-step countercurrent leaching. The vanadium leaching percent have growth and decline relation to occupation ratio of vanadium in in-soluble silicoaluminate mineral.

结果表明：该工艺的最佳工艺参数如下，即时间3 h、温度150 ℃、液固比1.21、硫酸用量25%、85%矿石粒度粒经小于0.095 mm；在此条件下，钒的一段浸出率为77%左右，而矿石经过两段逆流浸出后，钒浸出率可达90%；钒浸出率与矿石中难溶硅铝酸盐相中的钒占有率呈现消长关系。

Applying the grey correlation methods, this paper analyzed the correlation of slaking durability and granularity fractal characteristics of red bed weak rock as well as the experimental data of mineral and chemical component.

摘要采用灰色关联度法对红层软岩的粒度分形特征以及矿物、化学成分试验数据与其崩解性进行了关联分析。

By a comprehensive analysis of cores and thin sections and other data, detailed studies have been made on the rock types, granularity and sedimentary structures of the sublacustrine fan of Interval 6 of Yanchang Formation of Upper Triassic in the southwestern Ordos Basin.

通过岩心观测、薄片观察和各种资料的综合分析，对鄂尔多斯盆地西南部上三叠统延长组长6油层组湖底扇的岩石类型、粒度特征、沉积构造等特征进行了详细研究。

The effects of various factors, such as sulfurization time, temperature, sulfurization pressure, the concentration of sulfureted hydrogen, the concentration of hydrogen, granularity of catalyst and so on, are studied.

利用程序升温硫化技术，对负载在不同载体上的Co和Mo系催化剂的硫化过程进行了研究，分析了活性组分Co、Mo在催化剂硫化过程中的形态变化以及催化剂的硫化机理，同时还探讨了载体在催化剂硫化过程中的作用。

The crucial procedure of contour detection for microscopic image of sprayed droplets and measurement of granularity is to segment droplets from background by producing binary images. The singular threshold is uneffective because the image is very different in illumination. In this paper, a fast maximum entropy image thresholding algorithm based on local gray feature is presented to exact sprayed droplets from background and preserve contours of droplets.

雾滴图像的颗粒提取与测量关键是分割出雾滴与背景，生成二值图像，由于雾滴图像光照不均匀，用单一阈值无法兼顾亮区与暗区，本文提出了一种基于局部灰度特性快速最大熵动态阈值选择算法分割出雾滴微粒并提取雾滴轮廓。

But it is not suitable for the material of great granularity, big washiness and bad fluidity.

对粒度大、水分多、流态化性能差的物料不宜选用。

The paper discusses the relation of granularity with different washing methods and calcining temperatures.

重点研究了洗涤方式和煅烧温度对产物粒度的影响，根据XRD和IR实验数据，分析了粉体的组成结构、晶粒尺寸以及纳米粉体的形成原理。

This paper circumstantiates three issues to be solved for designing an effective and efficient web site mining algorithm, i.e., the sampling size, the analysis granularity, and the representation structure of web sites.

从站点的采样尺寸、分析粒度和描述结构3个方面分析了设计高效的Web站点挖掘算法所需要解决的问题。

The granularity of the former is usually coarser than the latter.

通常前者形成的沉积物比后者的粒度粗。

Chicken feed of model 661 is regarded as raw material of pellet feed, the influence that experimental factors including modulation-character temperature, modulation-character moisture, grease-additive quantity, and comminuting granularity have on making pellet quality, productivity, and electricity consumption. UG and ANSYS are regarded as simulating circumstance in finite element analysis, for problem on service life of the machine, evaluation index that average stress of a series of parameterized loop die is regarded as service life of hoop standard granulator is achieved by dynamic, static, and thermal structure coupling analysis for key part: loop die of the machine. For every influencing factor the experimental arrangement of array and combination is made by adopting optimizing idea and method of experimental design, the aim of quantification analysis is strived to arrive.

在试验设计中，采用正交试验的方法，以611型鸡饲料作为颗粒饲料的原料，分析混合饲料的调质温度、调质水分、油脂添加量、粉碎粒度等试验因素对制粒质量、生产率、电耗的影响；有限元分析中以UG、ANSYS作为仿真环境，针对制粒机使用寿命的问题，通过对环模制粒机中的关键零件环模进行动力、静力、热结构耦合分析，获得一系列参数化后的环模的平均应力作为环模使用寿命的评价指标；以实验设计的优化思想和有限元分析方法对各个影响因素作了排列组合式的实验安排，力求达到量化分析的目的。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。