查询词典 geometric drawing

Seven types of dimetric drawing and three types of trimetric drawing are introducedby the author with an aim to help hasten the shift of the principles derived from varioustypes of dimetric and trimetric projections from the theoretical approach to the field ofpractical use,and to alleviate the embarrassing situation that only the simple methodscan be resorted to in drawing the pictorial projections by isometric drawing and cabinetdrawing.

为了使各种形式的正二测和正三测从理论研究转向实际应用，克服长期来人们在绘制轴测图时，多数只能采用正等测和斜二测等单调情况，以及提高绘图速度，本文推荐采用七种正二测和三种正三测，并设计一套绘制这十种正轴测的专用工具--轴测多角比例尺。本文提出一套近似作这十种正轴测坐标面上椭圆的方法和数据，使其既简便又准确。

Through similar simulation test of block top-coal drawing, the influence of coal block size and block position in top coal on the recovery ratio and drawing manner is studied. It is found that the drawing manner has the different adaptation to the top coal which has different block distribution. The caving capacity is mainly decided by the block size. The top-coal which has layer difference of block with the same size has different recovery ratio. It is shown, that, to the given top-coal blocks, the recovery ratio of uniformly mixed blocks is maximal in the manner of drawing at interval of one support.

研究表明，顶煤块体大小是影响顶煤回收效果的主要因素，在顶煤块径一定的条件下，块体层位分布不同是造成顶煤回收率差异的主要原因，研究表明各级块度均匀混合时顶煤回收效果最好，块度从下向上增大分布次之，大块为中位顶煤时回收效果最差；各种放煤方式的适应性不同，各级块度均匀混合的顶煤适合用间隔放煤；块度从下向上增大适合用顺序放煤；大块在顶煤中位分布时，中硬煤以下适合用间隔放煤，硬煤应采用顺序放煤方式。

In a disk device, a base body (10) has a drawing lever (80) for inserting a disk, a discharge lever (100) for discharging the disk, and a slider mechanism for pivoting the drawing lever (80) and the discharge lever (100). The slider mechanism has a first cam groove for sliding a first pin of the drawing lever (80) and a second cam groove for sliding a second pin of the discharge lever (100). The drawing lever (80) pivots when the first pin slides in the first cam groove as the slider mechanism operates, and the discharge lever (100) pivots when the second pin slides in the second cam groove as the slider mechanism operates.

该光盘装置，在基座本体(10)上设置插入光盘的引入杆(80)、排出光盘的排出杆(100)以及使引入杆(80)和排出杆(100)转动的滑动机构；在滑动机构上具有使引入杆(80)的第一销滑动的第一凸轮槽和使排出杆(100)的第二销滑动的第二凸轮槽；通过第一销随着滑动机构的动作在第一凸轮槽内滑动，引入杆(80)进行转动，通过第二销随着滑动机构的动作在第二凸轮槽内滑动，排出杆(100)进行转动。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展方向作了简略概述；论述了冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具进行了设计：大直径三通管冲压复合模设计解决了大直径三通管的加工难题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模和盒形件侧壁小孔翻孔模。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,代写医学论文,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展方向作了简略概述；论述了冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具入行了设计：大直径三通管冲压复合模设计盖世了大直径三通管的加工难题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模和盒形件侧壁小孔翻孔模。

Finally, the paper presents a relatively complete plan for the reform of course system regarding such special topics as projection principles and basic drawing skills, applied foundation of projection graphics and general purpose computer assisted graphics software, mechanical drawing and general purpose computer assisted drawing software, special computer assisted drawing topics, etc.

多媒体计算机辅助教学以其声音、图像、动画、文字为一体的技术特点，为教学手段的现代化及教学课程体系的改革带来了很好的机遇。

Several affect factors of cylinder part limiting drawing parameter in deep-drawing were summarized in detail. Some new and practically applicable equations for estimating the limiting drawing parameter in the cup-drawing of a cylindrical cup with a flat-nosed punch are derived separately based on the load-maximum principle for localization of the plastic flow.

目前，国内外对极限拉深系数进行的研究较多，文献中详细地总结了板料成形中圆筒件极限拉深系数的若干影响因素，并基于最大承载原则提出了一些计算圆筒件极限拉深系数的实用公式。

The dynamics and heat transfer on the spinning line during the air drawing process are discussed in detail, mainly relating the forces acting upon the polymer along the spinning line and the expressions of the air drawing coefficient C〓 and heat transfer coefficient h. By introducing the power-law model as the constitutive equation to describe the theological properties of polymer melt and considering the changing of the density and specific heat capacity of polymer melt at constant pressure with the polymer temperature, the former model of polymer air drawing is improved and a complete polymer air drawing model is established, which is integrated with the model of air jet flow field of dual slot die.

在此基础上，对前人的聚合物拉伸理论模型进行了改进，以幂律模型作为描述聚合物熔体流变行为的本构方程，并考虑了聚合物熔体密度和定压比热随聚合物熔体温度变化而变化这个因素，从而建立了完整的熔喷聚合物拉伸理论模型。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,代写医学论文,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展方向作了简略概述；论述了冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具进行了设计：大直径三通管冲压复合模设计盖世了大直径三通管的加工困难的问题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模和盒形件侧壁小孔翻孔模。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展方向作了简略概述；论述砬冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具进好的了设计：大直径三通管冲压复合模设计盖世了大直径三通管的加工难题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模与盒形件侧壁小孔翻孔模。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48