查询词典 generating

In this paper, combining the technique of parallel computation with the numerical method of 3D eddy current field, we designed the algorithms of generating mesh, forming finite element equations and solving them in parallel on a shared memory multiprocessor (SGI Challenge L 8 CPUs), and presented a concrete and effective method.

本文将并行计算技术和三维涡流场计算方法相结合，对三维涡流场有限元分析的并行处理技术进行了细致的研究，设计了基于共享内存并行计算机(SGI Challenge L 8 CPUs)的网格剖分并行算法和三维涡流场有限元方程形成和求解的并行算法，为数值求解实际三维涡流问题提供了一种有效途径和具体方法。

We proved that the Cayley graphs of order $pqr$ are edge-Cayley graphs if its generating set has an element of order $p$.

证明了$pqr$阶群上的Cayley图，当其生成集中含有p阶元时，Cayley图是边-Hamilton图。

It was found that lead oxides (including PbO and Pb〓O〓) reacted chemically with PTFE when heated in vacuum, generating PbF〓, element C, and lead carbides.

研究表明，铅氧化物（包括黄色氧化铅PbO和红色氧化铅Pb〓O〓）在无氧加热条件下均能同PTFE发生化学反应，生成PbF〓、单质C以及铅的碳化物。

According to generating finite element model by meshing for special-shaped section columns, a computer program using the digital iteration method for full range analysis of special-shaped columns is complied. By the analytical results,"M-φ" related curves are obtained, at the same time, differences of ductile behavior, and bearing capacity are analyzed.

通过异形柱截面的有限元单元网格划分，用数值方法编制了计算机分析程序，通过计算，可以得到以上各种截面柱的弯矩—曲率关系曲线，分析它们在延性和承载力等性能方面的差异。

According to generating finite element model by meshing for special-shaped section columns and the conversion of coordinate,a computer program considered sliding of reinforcement anchoring using the digital iteration method for full range analysis of special-shaped columns is complied.

通过异形柱截面的有限元单元网格划分及坐标变换，在本文确定的数值分析方法上采用FORTRAN90语言编制了考虑粘结滑移影响的钢筋混凝土异形柱截面N-M-φ关系全曲线的计算机程序。

Basing on the transfinite mapping concepts, the present author developed a program system with an automatic mesh generator for 2-dimensional finite elements and graphical display, which is capable of generating various types of element meshs including that of 4-node, 8-node and 9-node quadrilateral elements, automatically deals with boundary conditions and load information, so that it is convenient to apply finite elament method to practical engineering problems.

利用超限映射理论，建立了一个二维有限元网格自动生成和图形显示为一体的程序系统。该系统能生成多种类型的单元（4节点、8节点、9节点），自动处理边界条件和荷载信息，使有限元法能方便地运用于实际问题。

During the process of the system researching, A new mesh approach based on advancing front technique for triangle elements was studied. A practical method of generating hexahedron mesh for cellular element method through transfering lines into volumes was worked out. Moreover, a new hidden method for cellular models and a approach of forming stress images were also researched.

在软件研制过程中，提出一种基于前沿生成法的速度快、稳定性好的平面元胞元网格自动生成方法和三维六面体网格的线段转换法；根据元胞元模型的特点，提出一种稳健性较好的三维元胞元模型消隐方法；通过对应力图生成技术的研究，提出一种对等值线、色带图、浓淡图均适用的应力图快速生成算法。

The stratified flow, slug flow and asymmetry annular flow upstream become symmetry annular flow with uniform film thickness after the spin generating element. The liquid extraction ratio is only determined by the diameter and number of the sampling holes and independent of gas and liquid flow rate of the main pipe, and the gas extraction ratio is mainly controlled by the liquid flow rate of the main flow loop.

分析表明，取样流体中的液相质量流量与主流体液相质量流量的比值主要取决于取样孔的数目和大小，而取样流体中的气相质量流量与主流体气相质量流量的比值则与主管路液相流量有关。

This thesis is combined with the project－"design and exploitation of Automotive Constant Drive-Shaft", which is undertaken by the topic team. Based on the structural simplification to three-dimension solid models of ball-cage type and three column-shaft type constant velocity joint, and the three-dimension solid models are obtained by conversion engineering. Altair/Hpermesh software is used here for generating the finite element mesh of key parts of ball-cage type and three column-shaft type constant velocity joint.

本文结合课题组承担的"汽车等速驱动轴设计开发"项目，在对通过逆向工程方法获得的等速驱动轴的球笼式等速万向节和三枢轴式等速万向节三维实体模型进行结构简化的基础上，利用Altair/Hypermesh软件对球笼式和三枢轴式等速万向节的各关键零件进行了有限元网格划分。

The pipe wall with four 2.5 mm diameter sampling holes and a spin generating element mounted upstream for modifying the inlet flow pattern are set up to improve the representative of the sampled fluid.

管壁四周均匀布置4个直径为2.5 mm的取样孔，并在上游采用旋流叶片将来流整改成液膜厚度均匀分布的环状流型，从而增强了取样的代表性。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。