查询词典 gears

This removal of air from the pump casing produces a partial vacuum on the pump inlet ,here the fluid is trapped between the teeth of the upper and lower gears and the pump casing .continued rotation of the gears forces the fluid out of the pump discharge .

这种泵内空气运动使泵吸入口处形成了真空，于是外部油箱的液体在大气压的作用下，由泵的入口进入，聚集在上下齿轮和泵壳体之间，齿轮连续的旋转使液体流出泵的出口。

The research indicates that it is just such deformation and center distance changing gives rise not only to gears hot, noise and vibration, but also result in higher energy consuming and lower fatigue life to the gears, gear shaft and bearing.

研究表明，正是由于这种中心距增减而引起的齿轮倾轧，不仅会导致齿轮发热、产生噪音及振动，而且还会降低齿轮、齿轮轴以及轴承的疲劳寿命和增加能耗等。

The main series products cover three aspects such as driven gears of motorbikes, electronikc power dual pinion wheels, automobile chain wheels, pulley wheels, valve guide, seat bush, signal wheels, disc, and bearing covers, electrical rear driven bridge powder metallurgical wheel and speed different gears. The parts also cover series for clutch plates for trains and automobiles air conditioning compressors as well.

产品系列包括：摩托车从动齿轮、电起动双联齿轮系列；汽车发动机链轮、皮带轮及气门导管、座圈、信号轮、相位盘、轴承盖系列；电动车后驱动桥粉末冶金大齿轮及差速伞齿轮系列；火车、汽车用离合器面片、空调压缩机粉末冶金零件系列。

Pre-grinding gear hobs are widely used as the rough machining cutters for hardened gears with high precision, for they can leave undercut at the root of the gears'teeth.

由于磨前齿轮滚刀能够使得被加工齿轮轮齿根部产生一定量根切，所以被广泛用作高精度硬齿面齿轮的粗加工刀具。

While most developments evolve over time, some are revolutionary. Ten years ago, helical gears for automobiles were machined from round forgings or bar stock. Today, high-volume gears are cold-extruded or hot-forged with gear teeth in a finished or nearly finished geometry.

大部分产品开发需要时间，有些是一场革命。10年前，汽车用螺旋齿轮还是利用圆锻件或棒材经过机加工制成，可是今天大体积的齿轮都是经过冷挤压或热锻造制作，轮齿的几何图形一次成型或接近成型。

Based on meshing principle of involutes gears, this paper deduces proper engagement equations for transmission mechanism with dual-idle gears .

根据渐开线齿轮啮合原理，推导出双惰轮传动机构的正确啮合条件等式，并根据等式编程求解，设计悬索桥主缆缠丝机的双惰轮传动机构。

However, as a result of the calculation and regulation error of cutting machine, the spiral bevel gears that are produced by cutting once are difficult in attaining good contact and transmission quality. Therefore, it is necessary to simulate the transmission of real gears and then to find optimal cutter and cutting machine parameters.

但是，由于人为计算和生产、调整过程的误差，一次试切加工出的弧齿锥齿轮一般难以达到最佳的接触传动质量，因此根据现有切削参数对弧齿锥齿轮进行接触传动的仿真，从而找出较好的切齿刀盘和机床调整参数是非常必要的。

The main products are: R Series Hardened helical gear reducer, S series helical gears - worm reducer, K Series helical gears - spiral bevel gear reducer, F series parallel shaft helical gear reducer, T series of spiral bevel gear to me , RV series aluminum alloy Worm Gear reducer, MB series of mechanical friction planetary CVT, hardened cylinder gear reducer and specifications of the various types of special gear, the worm reducer the design and manufacture.

R系列硬齿面斜齿轮减速机、S系列斜齿轮-蜗轮减速机、K系列斜齿轮-螺旋伞齿轮减速机、F系列平行轴斜齿轮减速机、T系列螺旋锥齿轮转向箱、RV系列铝合金蜗轮蜗杆减速机、MB系列行星摩擦式机械无级变速器、硬齿面圆柱齿轮减速机及各类特殊规格的齿轮、蜗轮减速机的设计制造。

The build-up welding of the meshing surfaces of big gear wheels :During operations of the big driving gears of big rolling mills and squeezers, the meshing surfaces wear easily and form cavities due to the squeezing force and attrition with the thinning of the gears resulting in the rejection of the gear wheels.

大齿轮咬合面堆焊：大型轧机和压榨机的传动大齿轮在工作过程中，齿的咬合面产生大的挤压力和磨擦力易磨损和形成凹坑，齿厚减薄，因而报废。

The RV reducer,which is a planetary gear system with cycloidal gears in contact with pin type internal gear teeth and involute gear pair,has been widely used as reduction gears of industrial robots, By reason that robots are very strict with vibrations,a dynamic model of RV reducer is developed.

建立RV减速器的动力学模型并推导运动微分方程，通过求解振动方程得到系统的固有频率，并就针轮齿数对RV减速器振动的影响等进行了研究，得到对RV减速器的设计和应用具有指导意义的结论。

The circulation, consumption and reproduction of the trilogy have not only testified to its historical significance and literariness, but also invested it with new meanings.

该三部曲的流通、消费与再生产不仅验证了其历史意义及文学性，而切还赋予它以新的意义。

If he thought that he could buy me off, he would be wrong.

如果他认为他可以收买我，那他就大错特错了。