查询词典 gear wheel

When the electrical work is running its principles, through chain-major axis rotation velocity, the major axis through the chain sprocket drive gear wheel ends, gear and spline drive for both the

其工作原理是当电机运转后，通过链传动带动长轴转动，长轴的两端通过链条链轮带动齿轮转动，齿轮、齿条带动两头的三级滑叉作横向同步运动。

When the electrical work is running its principles,through chain-major axis rotation velocity,the major axis through the chain sprocket drive gear wheel ends,gear and spline drive for both the horizontal cross-piece simultaneous movement.

其工作原理是当电机运转后，通过链传动带动长轴转动，长轴的两端通过链条链轮带动齿轮转动，齿轮、齿条带动两头的三级滑叉作横向同步运动。

When the electrical work is running its principles,through chain-major axis rotation velocity, the major axis throughthe chain sprocket drive gear wheel ends, gear and spline drive forboth the

其工作原理是当电机运转后，通过链传动带动长轴转动，长轴的两端通过链条链轮带动齿轮转动，齿轮、齿条带动两头的三级滑叉作横向同步运动。

When 'taking-off' I simply 'taxi' on three wheels until I am moving at least 5 to 10 kph, then jerk the steering wheel to the right which lifts the bike off of the landing gear wheel.

当'起飞'我只是'的士'三个轮子，直到我移动至少5至10公里，然后挺举方向盘右边的升降机自行车起飞的起落架舱。

6Hyperboloid initiative gear wheel axle assign above driven gear centre, easy to realize many axle transaxle well versed in, increase the height of unsticking of the drive shaft.

3双曲面齿轮传动的主动齿轮直径及螺旋角都较大，所以相啮合轮齿的当量曲率半径较相应的螺旋锥齿轮为大，其结果使齿面的接触强度提高。

The sectoring gear is a device for converting the rotary motion of the steering wheel into straight-line motion.

四，转向系统 Steering Gear 转向器的作用是把方向盘的旋转运动变为连杆机构的直线运动。

First ,make up the main parts'structure and the key designing parameters; thus reference to the similar driving axle structure , decide the entire designing project ; fanially check the strength of the axle drive bevel pinion ,bevel gear wheel , the differentional planetary pinion, differential side gear , full-floating axle shaft and the banjo axle housing , and the life expection of carrier bearing .

本文首先确定主要部件的结构型式和主要设计参数；然后参考类似驱动桥的结构，确定出总体设计方案；最后对主，从动锥齿轮，差速器圆锥行星齿轮，半轴齿轮，全浮式半轴和整体式桥壳的强度进行校核以及对支承轴承进行了寿命校核。

The edges of all steel components are beveled and polished, and each tooth of each gear wheel is manually polished with a rotating hardwood disk to reduce friction at the wheel contact points.

所有的不锈钢部件边缘都被倒角抛光，并且每一个齿轮的齿都被硬木转盘手工旋转抛光以减小齿轮接触点间的摩擦。

Locator, also known as wheel gear wheel organ, backup pad, block positioner, stop etc., is high intensity of natural rubber vulcanized high pressure synthesis, compression performance, and the slope has some flexibility, black and yellow with reflective material compliance with international standards, clearly visible and has slow down, non-slip, wear, reduce tire wear and so on.

定位器又称车轮挡轮器、倒车垫、阻位器、挡车器等，是采用高强度天然橡胶经硫化高压合成，抗压性能好，而且坡体有一定柔软度，黑黄相间含反光材料符合国际标准，醒目明显并具有减速、防滑、耐磨、减轻对车辆轮胎的磨损等特点。

Theme is the gerotor pump of Figure 2.9b,where the crescent moulding is dispensed with by using an internal gear with one less tooth than the outer gear wheel.

由于叶片末端是紧靠在壳体上的，所以这里几乎没有渗漏，但是由此叶片末端或者是内壳的磨损却十分严重。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。