英语人>网络例句>gear cutter 相关的网络例句
gear cutter相关的网络例句

查询词典 gear cutter

与 gear cutter 相关的网络例句 [注:此内容来源于网络,仅供参考]

Based on the one to one correspondence of the points on the tooth trace of plunge shaving cutter and the shaved gear, a method used to calculate the axial modification of the plunge shaving cutter when processing a crown gear is proposed.

用抛物线近似表示被剃齿轮的齿向鼓形量,采用一一对应映射方式将被剃齿轮的齿向鼓形量加到径向剃齿刀理论齿向线上各对应点的修形量上,得到加工鼓形齿轮的径向剃齿刀最终齿向修形量。

Analyse the tooth geometry of Klingelnberg Cyclo-Palloid spiral bevel gear.,according to the relative position and kinematic relation of the cutter heads,virtual crown gear and the processed wheel blank,established the system of coordinates of the gear cutting, dedcuced the tooth face equation of the virtual crown gear, according to relations of the gear cutting and space theory of engagement, deduced the tooth face equation of klingelnberg Cyclo-Palloid spiral bevel gear, and drawing the three-dimensional graphs of the virutal crown gear and Klingelnberg Cyclo-Palloid spiral bevel gear according to the design and setting parameters.

根据铣齿加工中刀盘、摇台和轮坯的相对位置和相对运动关系建立了切齿啮合坐标系,由矢量的旋转推导了产形轮齿面方程;根据空间啮合原理和切齿啮合关系推导了被加工齿轮的齿面方程;由设计参数和铣齿调整参数计算得到齿面离散数据,绘制了产形轮和摆线齿锥齿轮的三维齿形。

While carrying out simulative program design for hobbing machining,the most difficult point is the description and modelling on the relationship between the cutter and gear blank both in space and in motion,especially the modelling of motion relation between cutter and gear blank in case there exists factors of error.

在进行滚齿的切削仿真程序设计中,其中最大的难点是对刀具和轮坯的空间关系和运动关系的描述和建模,尤其是存在误差因素时对刀具和轮坯之间运动关系的建模。

Main applicability: Welding of the miamond knife head, the carbide alloy saw bit , machine work use carbide alloy cutter welding, if the cutting tool welding such as miamond cutter , drilling tool , lathe tool , shaper tool , milling cutter , broach; Standard piece , hot bolt rammer, if high-strength bolt , nut etc.; Hardware implement , handwork implement heat treatment, if tongs , spanner , whorl utensil , hammer , axe; The accessory high frequency quenching sells the various automobile accessory , motorcycle at reduced prices, such as: Crank shaft , connecting rod , wrist pin , crank pin , sprocket , axial cam , air valve , various rocker arm , rockshaft; Within speed change box, the various gear wheel , castellated shaft , biography prop up high frequency quenching treatment such as half axes , various small axis , various shift fork; The part heat treatment , the high frequency quenching that the gear wheel , sprocket , various axis , castellated shaft , pin wait for if various handle metal; Mssingle of face slide way quenching sells machine tool industry machine at reduced prices waiting.

主要适用范围:金刚石刀头的焊接,硬质合金锯片、机械加工用硬质合金刀具的焊接,如金刚石刀具、钻具、车刀、刨刀、铣刀、铰刀等刃具的焊接;标准件、螺栓的热镦,如高强度螺栓、螺帽等;五金工具、手工工具的热处理,如钳子、扳手、旋具、锤子、斧头;各种汽车配件、摩托车配件的高频淬火处理,如:曲轴、连杆、活塞销、曲柄销、链轮、凸轮轴、气门、各种摇臂、摇臂轴;变速箱内各种齿轮、花键轴、传支半轴、各种小轴、各种拨叉等高频淬火的处理;金属零件的热处理,如各种齿轮、链轮、各种轴、花键轴、销等的高频淬火处理;机床行业的机床床面导轨的淬火处理等。

Ifs use finger shape milling cutter or a dish of shape piece of milling cutter adopt single tooth dispart law cutting time, cans process straight teeth, skewed tooth, a garden of stud gear and bring groove double helical gear or worm gear, this moment was processed gear's dentiform then by cutting tool become shape.

若用指形铣刀或盘形片铣刀采用单齿分度法切削时,可加工直齿、斜齿、园柱齿轮及带槽人字齿轮或蜗轮,此时被加工齿轮的齿形则由刀具成形。

Based on the relevant movement between hard shaper cutter and grinding wheel, the movements of grinding wheel are studied. The shaping grinding point and the shaping grinding edge are made up with. In order to easily compare when shaping errors and cutting edge"s angles are the most excellent, uniform expressions for convex curved rake face of hard shaping cutter and spatial cutting edge curve are separately developed. The distributions of new profiling cutter"s shaping errors and cutting edges angles are analyzed. The relevant grinding wheel and cam are designed. Due to this paper, a new profiling hard shaping cutter has been manufactured successfully. At last experiments are made to test the performance of hard shaping cutter and all kinds of precision of hard gear.

本文直接从插齿刀与砂轮之间的相对运动关系出发,单独研究砂轮的运动,提出砂轮成形磨削点和砂轮成形磨削刃的概念;分别建立圆柱砂轮和圆锥砂轮磨削后硬齿面插齿刀的波形前刀面方程及空间切削刃方程;为便于比较何种情况下插齿刀的构形误差和切削角度能同时达到最优,分别对磨削五种不同硬齿面插齿刀所用的砂轮进行了廓形设计,并分析了插齿刀的构形误差和侧切削刃切削角度的分布规律;为插齿刀波形前刀面的磨削加工设计了相应的凸轮,用所设计的凸轮和近似的砂轮成功地制造出新构形法硬齿面插齿刀;最后进行插齿加工试验,检验新构形法硬齿面插齿刀的抗崩刃能力、耐磨性及被加工硬齿面齿轮的各项精度。

Bulk volume of the volume of block block block caliper micrometer-specific block, such as special types of straight shank drill bits Serratula straight shank long twist drill set, such as alloy straight shank twist drill reamer type of hand reamer straight shank straight shank machine reamer taper shank machine reamer and other types of coarse tooth cutter straight shank cutter tooth taper shank Rough Milling fine-tooth cutter straight shank end mill, such as hand-tap machine tap tap tap left teeth straight pipe tap, such as garden die die die left teeth straight pipe die die US-made of other alloys such as Alloy blade machine Segment saw blade, such as gear type inverted roller gear Gear planing cutter knife disc-shaped gear gear shaper cutters, such as factory outlets: cast iron flat, square boxes, granite slab, square and so on.

量块 散量块卡尺专用块千分尺专用块等钻头类直柄麻花钻直柄长麻花钻镶合金直柄麻花钻等铰刀类直柄手铰刀直柄机用铰刀锥柄机用铰刀等铣刀类粗齿直柄立铣刀粗齿锥柄立铣刀细齿直柄立铣刀等丝锥手用丝锥机用丝锥左牙丝锥直管丝锥等板牙园板牙左牙板牙直管板牙美制板牙等其他合金刀头合金刀片机用锯条等齿轮倒类齿轮滚刀齿轮刨刀齿轮铣刀盘形插齿刀等厂家直销:铸铁平板、方箱、花岗石平板、直角尺等。

The main products are as follows: straighten cutter (diameter:Φ1.0-Φ9.0 mm), multi-functional precision governor can straighten cutter, the Chen Shui-bian straighten cutter, strip-precision gears for a deduction machine, Gear-precision sheet of the Chen Shui-bian deduction, a deduction of Gear,(D deduction / 1.30 deduction / belt deduction, etc.) for a deduction, S-hooks linked to a deduction, a deduction of computer-balanced machine, racks / Pants-steel deduction for a deduction, automatic racks hook Forming / rubbing teeth Siamese mix, automatic racks hook Roll Machine, automatic keychain combination of machines, semi-automatic hydraulic bending box machine, grinding needle chamfering machine ,(Car Aberdeen axis / linked to a) spend rubbing machine, Network Rail repair Machine, Hydraulic automatic machine Daquan (diameter Φ1.5 ~Φ10 mm)(Circle Drive:Φ25-Φ1000 mm) series, such as wire and machinery specialized for processing Zero, and accessories.

主要产品如下:调直切断机(线径:Φ1.0-Φ9.0mm)、多功能精密可调速调直切断机、方扁调直切断机、扁线机、精密齿轮式打扣机、齿轮式精密薄片扁扣机、齿轮式打扣机、(D扣/三角扣/皮带扣等等)打扣机、S钩挂钩打扣机、电脑平衡杆打扣机、衣架/裤架钢扣打扣机、全自动衣架钩成型/搓牙组合连体机、自动衣架钩搓牙机、全自动钥匙圈组合机、半自动液压弯框机、磨针倒角机、搓花机、铁网修边机、液压全自动打圈机(线径Φ1.5~Φ10mm)(圈径:Φ25-Φ1000mm)等系列线材加工专用机械及零、配件。

After gear shaving cutter profile correction,the smooth and steady of the run of the toothed gear changes obviously,at the same time, gear shaving cutter profile correction reduces noises and improves the bearing capacity of the toothed gear and makes its life long.

通过对剃齿刀的修形,剃齿后明显改变了齿轮运转的平稳性,降低了齿轮的噪音和振动,提高了承载能力,延长了齿轮的使用寿

For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. The cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed; and a new method of choosing deflection factor by using limited area is presented.

研究加工不等齿厚的非标准参数渐开线齿形,与非渐开线齿形复合的锁闭齿轮插齿刀刀齿的排列、刀具齿数的选择以及刀具设计的基本方法,介绍用限制区域选择插齿刀变位系数的新方法,并给出刀具齿顶后角与侧螺旋角的关系曲线,为插齿刀参数的选择提供依据。

第3/9页 首页 < 1 2 3 4 5 6 7 8 9 > 尾页
推荐网络例句

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国,慢性酒精中毒,肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题,你可以随时联系我。

Very pretty, but the airport looks more fascinating The other party wisecracked.

很漂亮,不过停机坪更迷人。那人俏皮地答道。