查询词典 gate valve

Normally closed solenoid valve, coil power, the GATE VALVES armature under the action of electromagnetic force driving the first Vice-valve valve Seti, the main valve on the valve cup of fluid flow out through the Vice-valve, reducing the role of the main valve pressure on the valve cup, when the main valve valve to reduce pressure on the cup to a certain value, the armature driving the main valve valve cup, and use pressure Ershi main valve valve cup opening, medium flow.

常闭电磁阀，线圈通电后，衔铁在电磁力作用下先带动副阀阀塞提起，主阀阀杯上的流体经副阀流走，减少了作用在主阀阀杯上的压力，当主阀阀杯上的压力减少到一定值时，衔铁带动主阀阀杯，并利用压差而使主阀阀杯开启，介质流通。

The valve gate unit has a valve pin for controlling the flow of the molten plastic from a hot runner system to an injection chamber and an activating unit coupled with the valve gate unit.

阀门单元具有一被用来控制从一热流道系统到一注射腔室的熔化塑料流的阀销以及一与阀门单元连接的致动单元。

7 Gate valve according to Table 6, the main component material selection, supply and demand any special requirements by mutual agreement in order the contract.

4.15.7闸阀主要零件材料可按表6选取，如有特殊要求经供需双方协商在订货合同中注明。

The drawback is that operating torque, operation, easy to make body, stem damage, especially in large-diameter gate valve.

其缺点是操作力矩大，操作时易使阀体、阀杆损坏，特别是大口径闸阀。

The following cases, to go with locator: 1, medium pressure high pressure big time; 2, valve diameter is large Forged Gate, Globe, Check Valves (DN 00); 3, high or low temperature control valve; 4, the action necessary to raise the speed control valve; 5, using standard signal, the operation of non-standard spring when the implementing agency (20 ~ 100KPa spring outside the range); 6, when used for sub-process control; 7, when the valve to achieve the reverse action (air to close each open-type gas conversion); 8, need to change the valve's flow characteristic time (you can change the positioner cam); 9, no spring actuator or piston actuator, the proportion of action to achieve the time; 10, electrical signals to operate pneumatic actuator must Distribution - gas valve positioner.

下列情况下，要配定位器： 1、介质压力高、压差大的时候； 2、调节阀口径大时（DN00）； 3、高温或低温调节阀； 4、需要提高调节阀的动作速度时； 5、用标准信号、操作气动管路截止阀非标准弹簧的执行机构时（20～100KPa以外的弹簧范围）； 6、用于分程控制时； 7、使阀门实现反向动作时（气关式和气开式互相转换）； 8、需要改变阀的流量特性时； 9、无弹簧执行机构或活塞执行机构，要实现比例动作时； 10、用电信号去操作气动执行机构时，必须配电-气阀门定位器。

Double Flanged Style Valves bolt up similar to a bolted cap swing check or gate valve.

双法兰类型阀门采用螺栓紧固，类似于螺栓阀帽旋启式止回阀或闸阀。

Normative references GB 150 steel pressure vessel GB 152.1 ~ 152.4 fastener hole and Shen Kong GB 196 commonDast Gate Valves thread of basic dimensions (diameter l ~ 600mm) GB 197 common thread of tolerance and fit (diameter of 1 ~ 355mm) GB 798 live bolt GB 897 stud bm = ld GB 898 stud bm = 1.25d GB 901 Dlass B and other long stud GB 5782 Hexagon head bolts B and B class GB 5796.1 ~ 5796.4 Dl 150, 300, 600 Lb Dast Steel Gate Valvestrapezoidal thread GB 6175 2 Hexagon nut B and B class GB 9112 types of steel pipe flanges GB 9113.1 ~ 9113.26 Integral steel pipe flanges GB 12220 Universal Valve Logo GB 12221 length of theDl 900, 1500 Lb Dast Steel Gate Valves valve structure of metal flange GB 12222 Multi-turn valve actuator attachment GB 12224 General requirements for steel valves GB l2228 General Valve carbon steel forgings GB 12229 Universal Valve carbon steel castings GB 12230 Universal Valve austenitic steel castings GB / T 12252 General requirements valve supplier ZB Jl6 006 test and test valve 原文来源:http://www.1zhafa.com

引用标准 GB 150 钢制压力容器 GB 152.1～152.4 紧固件通孔及沉孔 GB 196 普通螺纹基本尺寸(直径l～600mm) GB 197 普通螺纹公差与共同(直径1～355mm) GB 798 活节螺栓 GB 897 双头螺柱bm＝ld GB 898 双头螺柱bm＝1.25d GB 901 等长双头螺柱 B级 GB 5782 六角头螺栓 B和B级 GB 5796.1～5796.4 梯形螺纹 GB 6175 2型六角螺母 B和B级 GB 9112 钢制管法兰类型 GB 9113.1～9113.26 整体钢制管法兰 GB 12220 通用阀门标记 GB 12221 法兰连接金属阀门结构长度 GB 12222 多回转阀门驱动装配的连接 GB 12224 钢制阀门一般要求 GB l2228 通用阀门碳素钢锻件技术条件 GB 12229 通用阀门碳素钢铸件技术条件 GB 12230 通用阀门奥氏体钢铸件技术条件 GB/T 12252 通用阀门供货要求 ZB Jl6 006 阀门的试验与检验

Normative references GB 150 steel pressure vessel GB 152.1 ~ 152.4 fastener hole and Shen Kong GB 196 common Cast Gate Valves thread of basic dimensions (diameter l ~ 600mm) GB 197 common thread of tolerance and fit (diameter of 1 ~ 355mm) GB 798 live bolt GB 897 stud bm = ld GB 898 stud bm = 1.25d GB 901 Class B and other long stud GB 5782 Hexagon head bolts A and B class GB 5796.1 ~ 5796.4 Cl 150, 300, 600 Lb Cast Steel Gate Valves trapezoidal thread GB 6175 2 Hexagon nut A and B class GB 9112 types of steel pipe flanges GB 9113.1 ~ 9113.26 Integral steel pipe flanges GB 12220 Universal Valve Logo GB 12221 length of the Cl 900, 1500 Lb Cast Steel Gate Valves valve structure of metal flange GB 12222 Multi-turn valve actuator attachment GB 12224 General requirements for steel valves GB l2228 General Valve carbon steel forgings GB 12229 Universal Valve carbon steel castings GB 12230 Universal Valve austenitic steel castings GB / T 12252 General requirements valve supplier ZB Jl6 006 test and test valve

引用标准 GB 150 钢制压力容器 GB 152.1～152.4 紧固件通孔及沉孔 GB 196 普通螺纹基本尺寸(直径l～600mm) GB 197 普通螺纹公差与配合(直径1～355mm) GB 798 活节螺栓 GB 897 双头螺柱bm＝ld GB 898 双头螺柱bm＝1.25d GB 901 等长双头螺柱 B级 GB 5782 六角头螺栓 A和B级 GB 5796.1～5796.4 梯形螺纹 GB 6175 2型六角螺母 A和B级 GB 9112 钢制管法兰类型 GB 9113.1～9113.26 整体钢制管法兰 GB 12220 通用阀门标志 GB 12221 法兰连接金属阀门结构长度 GB 12222 多回转阀门驱动装置的连接 GB 12224 钢制阀门一般要求 GB l2228 通用阀门碳素钢锻件技术条件 GB 12229 通用阀门碳素钢铸件技术条件 GB 12230 通用阀门奥氏体钢铸件技术条件 GB/T 12252 通用阀门供货要求 ZB Jl6 006 阀门的试验与检验

Cut off cut-off valve is mainly used for fluid pathway, including the cut-off valves, gate valves, plug valves, ball valves, butterfly valves, diaphragm valves, control API Cast Steel Valves valves and other folders; The main control valve for regulating fluid pressure, flow, etc., including control valve, throttle, valve and float valve, etc.; Check valve used to prevent reverse flow of fluid; Shunt valve fluid channel for distribution of destination, or two-phase separated, including slide valves, multi-valve, trap, and emptying valves and so on; Safety valve is mainly used for security, to prevent the boiler, pressure vessel or pipeline overpressure due to the damage; Multi-valve is a valve with more than one function, such as the cut-off valve can both start and end back from the role of the role of drying.

截断阀主要用于截断流体通路，包括眼镜阀截止阀、闸阀、旋塞阀、球阀、蝶阀、隔膜阀、夹管阀等；调节阀主要用于调节流体的压力、流量等，包括调节阀、节流阀、减压阀和浮球调节阀等；止回阀用于阻止流体的逆向流动；分流阀用于分配流体的通路去向，或将氧气专用阀、铜阀门两相流体分离，包括滑阀、多通阀、疏水阀和排空气阀等；安全阀主要用于安全保护，防止锅炉、压力容器或管道因超压而破坏；多用阀是具有一种以上功能的阀门，如截止止回阀既能起断流作用又能起止回作用。

Introducing the structural characteristics and operation conditions of double seal hydraulic flat gate valve for slurry transportation pipeline, describing simply the making, application and maintenance of valves.

介绍了适用于浆体输送管线的双密封液动平板闸阀的结构特点及性能，叙述了其制造、使用及维护方

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。