查询词典 gas welding

Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.

熔点880℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁

Reduce the melting zone porosity methods include: welding pre-cleaning, welding process using inert gas welding area and selection of the full protection of the lower cooling rate of the welding parameters.

降低熔化区气孔率的方法包括：焊前清洗、焊接过程中用惰性气体充分保护焊接区和选择较低冷却速度的焊接参数。

If a joint is in the cable, the temperature of the tinning welding joint is mot more than 120℃,compressing joint mot more than 150℃ and electro-welding or gas-welding joint not more than 250℃.

2.2.2 短路时（最长持续时间不超过5秒），导体最高温度不超过250℃，电缆线路中间有接头时，锡焊接头不超过120℃，压接接头不超过150℃，电焊或气焊接头不超过250℃。

Compared with arc welding, gas welding flame temperature is low, heat dispersion, heat slowly, so productivity is low, the workpiece deformation of serious, large welding heat affected zone of welded joint quality.

它与电弧焊相比，气焊火焰的温度低，热量分散，加热速度缓慢，故生产率低，工件变形严重，焊接的热影响区大，焊接接头质量不高。

ABSTRACT The research of metal transfer in metal gas arc welding is of great significance for the control of arc welding process and quality, the improvement of existing welding technology and the development of new welding equipment. With the powerful aid of welding arc spectrum which contains plenty of information of metal droplet transfer, this dissertation, which mainly aims at putting forward an effective detecting method with arc spectrum signal, has inspected the spectrum of metal gas welding arc and discovered their dynamic characteristics of each kind droplet transfer mode.

熔化极气体保护焊熔滴过渡的研究，对于焊接过程及质量控制、焊接工艺方法的改进和新型焊接设备的推出都具有重要意义，而熔化极气体保护焊电弧光谱中含有丰富的反映熔滴过渡的信息。

Other ancillary processing equipment are: welding machine, the protection of carbon dioxide gas welding, spot welding, riveting pressure machine, the general press, tapping machine, and so on.

其它的辅助加工设备有：氩弧焊机、二氧化碳气体保护焊机、点焊机、压铆机、普通冲床、攻丝机等。

PP-H welding method is commonly used in thermal contact welding and the use of hot gas welding electrode.

PP-H 的焊接常用的方法是热接触焊接和使用焊条进行热气焊。

Can be cut 1mm-60mm thick, plasma cutting machine, oxyacetylene cutting machine, dc welding machine, welding, gas welding, arc welding of carbon dioxide and other auxiliary equipment.

可割1mm-60mm厚的等离子切割机，氧乙炔切割机，直流氩弧焊机，电焊，气焊，二氧化碳保护焊等辅助设备。

It is suitable to be used as filling material for oxygen-acetylene gas welding and carbon arc welding, and also for manual braze welding. It is the ideal material for welding of copper alloy, copper, gray cast iron and hard alloy knife and etc.

HS221 JIS ZYCusN 适用于氧-乙炔气焊及碳弧焊时作为填充材料，也可用于钎焊，是铜合金、钢、灰铸铁及硬质合金刀具等焊接材料中较为理想的焊接材料。

The droplet transfer of twin-wire co-pool gas shielded metal arc welding process takes great effects on the behavior of the molten pool by transferring energy, momentum and fluid flow to the molten pool which will affect the weld appearance.

双丝共熔池GMAW(twin-wire co-pool gas shielded metal arc welding， TCGMAW)熔滴过渡对焊缝成形的影响体现在对熔池的作用上，熔滴对熔池的作用在于向熔池传输能量、动量和质量，最终会影响到焊缝的成形和质量。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。