查询词典 fuse

This kind of analysis method can be directly used in the selection design of antenna dip angle and in the confirmation of accuracy target of fuse information transmission system and fuse information control system.

这种分析方法可直接用于对不同目标的引信天线倾角的选择设计及引信信息传输系统、信息控制系统的精度指标确定。

The length of the fuse is set to last until the shell reaches the proper altitude. At that point, the fuse ignites the bursting charge, which explodes the shell.

导火线的长度能够支持礼花弹到达一定的高度、到达指定高度后，导火线点燃爆炸点，使得礼花弹爆炸。

Temperature is divided into low-melting-point alloy fuse-shaped form with the trigger temperature shape memory alloy, etc. There are temperature fuse is easy to prevent heat or electrical heating appliances for the protection of high temperature, such as: hair dryer, electric iron, electric rice cookers, electric, transformers, motors, etc.; its temperature rise in response to the increased electrical power, would not care about the current size of the circuit.

温度保险丝又分为低熔点合金形与感温触发形还有记忆合金形等等（温度保险丝是防止发热电器或易发热电器温度过高而进行保护的，例如：电吹风、电熨斗、电饭锅、电炉、变压器、电动机等等；它响应于用电电器温升的升高，不会理会电路的工作电流大小。

Our company is one of the largest fuse manufactures of high/ low voltage fuse and fuse combinations in china.

公司是国内最大的高/低压熔断器、熔断器组合电器的生产商之一，产品有

Along with the developing of fuse-warhead matching technology, especially the integralization of fuse and guidance, the information transmission in fuse-warhead matching process has assumed three-dimensional tendency more and more.

随着引战配合技术特别是引信制导一体化技术的发展，引战配合过程中的信息传输越来越呈现出立体化趋势。

Fuse-link's trumper tip must be fixed between fuse cartridge and fuse cartridge holder.

用一个扳手卡住螺丝管端部螺栓，用另一个扳手旋紧末端螺栓，扭矩约5.6—7.9N.m。

Finally, I use the 5mmFMCW blasting fuse which was successfully developed to carry on the actual signal analysis. The 5mm FMCW blasting fuse is carried on the range coverage test .The 5mm FMCW blasting fuse is tested and analyzed when it and aims are simulated the junction, and we have drawn the important conclusion.

最后，利用研制成功的5mmFMCW引信进行了实测信号分析，主要是进行了5mmFMCW引信进行作用距离测试以及5mmFMCW引信模拟引信交会测试及分析，并得出了重要结论。

100KW factory specializing in the production of the following high-frequency machines, leading products: Automatic Blister molding machine, whole plant equipment ,5-30KW automatic synchronization slip Units fuse machine, double-headed synchronous machine fuse ,4-100KW automatic sliding Units welder, 4-15KW single turntable welder ,2-15KW welder-type double-headed foot, 8-25KW welder canvas ,4-15KW shielded single slip Units, rotary high frequency welding machine. 8-15KW environmental protection welder dedicated PET material, PP, PET, PVC plastic fuse box dedicated machines, ultrasonic plastic welding machine and so on.

本厂专业生产100KW以下高周波机器，主导产品：全自动吸塑成型机、整厂设备，5-30KW全自动滑台同步熔断机、双头同步熔断机、4-100KW全自动滑台熔接机，4-15KW 单头转盘熔接机，2-15KW双头脚踏式熔接机， 8-25KW帆布熔接机，4-15KW屏蔽式单头滑台、转盘式高周波熔接机。8-15KW环保料PET专用熔接机，PP、PET、PVC胶盒专用熔断机，超声波塑焊机等。

Compared the calculated curve and the real assay curve we can make a conclusion that: this method can calculate the melting time of the fuse at the huge short current (more than 50 times of the current rating) with the error less than 5%; the resistor and time characteristic can also be acquired, it provided the date for overvoltage calculation of the fuse model. The research of the overvoltage during fusing process is based on short circuit test of the fuse.

由计算结果与实际试验曲线对比可得：该种方法能够比较准确地计算出较大短路电流下(熔断器额定电流的50倍以上)熔断器的弧前时间，误差一般在5%以内；同时还可以算得熔断器在弧前的电阻时间特性，为开断过电压仿真计算电路中的熔断器模型提供数据。

The fuse pipe is the main part of fuse,it is made by installing the fuse wire in the porcelain pipe,filling the quartz sand in the porcelain pipe and sealing to-ends of pipe.

熔断管是熔断器的主要部件，它是由熔丝装在瓷管中，并在瓷管中充填石英砂，两端密封而成。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。