查询词典 furnace burden

The content of potassium oxide, sodium oxide and zinc oxide in blast furnace burden was simultaneously determined by inductively coupled plasma atomic emission spectrometry.

采用电感耦合等离子体原子发射光谱法同时测定高炉炉料中氧化钾、氧化钠和氧化锌的含量。

Burden distribution model for bell-less blast furnace is established based on mathematical knowledge and computer technology through the analysis of effect factors and characters of burden distribution.

针对高炉炉内料面的分布特征，通过分析和考虑无料钟高炉布料的影响因素及其特点，结合数学知识和计算机技术，建立了无料钟高炉布料模型。

The experiment results of burden distribution and burden surface profile are very identical with that of simulation. It proves amply the application of distinct element method in charging of bell-less top blast furnace is practicable and true.

离散单元法在高炉无钟炉顶布料中的应用是研究高炉无钟炉顶布料及炉料分布的一种新方法，高炉无钟炉顶布料离散单元法模拟模型的可行性和正确性只有通过实验验证和确认。

During computer calculate, According to condition of charging of bell-less top blast furnace, and burden motion characteristics and contact situation in charging process, the reboxing is used to distinguish the point of contact between burden granules and between burden granular and wall.

本文将其引入冶金工程科学研究，从高炉炉料颗粒的运动机理研究高炉无钟炉顶布料过程及布料规律，确立了高炉无钟炉顶布料的炉料分布和料面形状的理论数学模型，推动了高炉无钟炉顶布料的理论研究。

It effectively solves the problem of contact mechanics between burden granules. The dynamic data structure that is a linked list is built to save and delete the varying data in simulation calculation process. Therefore, the distinct element method simulation model of charging bell-less top blast furnace is established in view of the distinct element method model of blast furnace burden granular.

本文首先对离散单元法的基本原理和数值计算方法进行了系统研究，针对高炉炉料颗粒介质特点，对离散单元法进行了相应改进，建立了高炉炉料颗粒运动的离散单元法基本数学模型，推导出了相应的高炉炉料颗粒离散单元法数值计算基本参数的计算公式，例如阻尼、刚度、时步等，并确定了合理的数值模拟参数值。

This paper intreduces that in design of blast furnace charging equipment correct option of falling point po- sition of burden and correct option of small bell diameter can decrease and prevent the bisbell and big hoppor weared and impacted by furnace burden,so that the service life of these equipments can be increased,taking top cllarging equipment of No.

本文以济南钢铁总厂第二炼铁厂1￣＃高炉炉顶装料设备为例，简析了装料设备设计中，应考虑炉料落点位置，合理选择小料钟直径，目的是减少和避免炉料对大料钟与大料斗的冲击和磨损，提高使用寿命。

The campaign of induction furnace is lower because 10t main frequency furnace uses of acid refractory liner that is corroded by liquid iron and basic slag under the working condition of high temperature and full load and abr aded in the process of charging cold burden.

10t工频感应炉炉衬原采用酸性耐火炉衬，在高温满负荷工作状态下，受铁液及碱性炉渣侵蚀，加冷料过程中受机械磨损，造成感应炉炉龄低。

The technical measures of 750m3 blast furnace strengthening smelting of Laiwu iron and steel general works consist of improving the coke quality,increasing burden quality,promoting reasonable burden structure,determining reasonable adjustment parameters of upper and lower blast furnace,using the waste heat recovery device of hot stove and using the spraying and coating technique for making liner of blast furnace,etc.

莱钢750m3高炉强化冶炼的措施包括改善焦炭质量，提高入炉矿石质量，促进炉料结构合理；确定合理的上下部调剂参数，抓好炉前工作，应用INBA法新转鼓水渣处理系统、热风炉余热回收装置、高炉喷涂造衬等新技术。

According to the future trend of iron ore and the comparison of process and metallurgical properties, the hybrid pelletized sinter can replace the now compound burdens, it is the future trend of the blast furnace burden constitution.

从含铁原料的发展趋势和工艺过程以及冶金性能的比较，混合球团烧结矿完全可以替代现有的复合炉料，它是高炉炉料结构的发展方向。

On the basis of this model, combined with potential flow for expressing burden flow, considered with gas-solid heat exchange and main chemical reaction in shaft furnace, Comprehensive two dimensions mathematics model of shaft furnace is set up for analyzing flow, heat and mass transfer in furnace.

并在此基础上，结合反应固相流动的势流模型，综合考虑气固传热和竖炉内的主要化学反应，建立了竖炉二维综合数学模型，对炉内流动、传热及传质过程进行了解析。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷