friction相关的网络例句

查询词典 friction

与 friction 相关的网络例句 [注：此内容来源于网络，仅供参考]

Release agents, carbon black; tire release agents, mold release agents brakes, aluminum alloy release agent; friction material release agent; Alloy release agent; polyurethane elastomer release agent; cement product release agent; epoxy release agent; conveyor belt release agent; solar release agent; Rubber release agent; red pomade

脱模剂，碳黑；轮胎脱模剂、刹车片脱模剂、铝合金脱模剂；摩擦材料脱模剂；铝合金脱模剂；聚氨酯弹性体脱模剂；水泥制品脱模剂；环氧树脂脱模剂；输送带脱模剂；太阳能脱模剂；橡塑脱模剂；冲头油

Everyone know that make to move the result biggestly is an occurrence before tire lock die moment, if can let the car of system motive has been keep at with the appearance of the tire friction balance, will acquire to make to move the result biggestly so.

大家都知道最大的制动效果是发生在轮胎锁死前的瞬间，如果能够让剎车制动力一直保持在与轮胎摩擦力平衡的状态，那么将获得最大的制动效果。

Because the lock dead of the tire is the result that the car of system friction of motive and tire and ground compare, also be say that the car march forward whether a tire lock die or not of extreme limit is would with the condition that the characteristic, road of the tire face, position the angle, to press, hang the characteristic but" at any time different" of mourn the system.

由于轮胎的锁死是剎车制动力和轮胎与地面的摩擦力比较的结果，也就是说车子行进间轮胎锁死与否的极限是会随轮胎本身的特性、路面的状况、定位角度、胎压、悬吊系统的特性而『随时不同』。

It is investigated the tribological properties of tin dioxide nanoparticle modified with sodium oleate,the results exhibit that the modified tin dioxide nanoparticle can elevate the anti-wear and friction reduction performances of base Stock.

考察了用油酸钠改性的纳米二氧化锡的摩擦学性能，结果表明，改性纳米二氧化锡能够提高基础油的抗磨减摩性能。

According to the practical characteristics and parameters during hot finishing rolling process of aluminium alloy JP1235, a three-dimensional thermo-mechanical coupled elastic-plastic FEM model was established with the software Marc. And this model was used to simulate the rolling state of F1 stand without back tension. The lateral distribution of rolling force、contact friction force and other mechanic parameters were calculated. Meanwhile, simulated the rolling state considering the influence of mill tilt, and studied the distribution of the mechanics under this state, discussed the effect of mill tile on mechanic parameters and strip steering, which can provide some reference to steering control strategy.

根据JP1235铝合金板带热精轧过程的实际工艺特点和工艺参数，采用非线性有限元软件Marc，建立一个三维热力耦合弹塑性有限元模型，模拟了精轧机组第一机架（F1机架）失去后张力作用后的轧制状态，计算出轧制过程中轧制力、摩擦力等力能参数沿板宽方向上的分布情况，在此基础上，模拟初始轧辊倾斜影响下的轧制状态，并对该轧制状态下的力能参数分布情况进行研究，探讨轧辊倾斜对力能参数分布及跑偏规律的影响，为纠偏控制提供了一定的理论依据。

Low Open and Close Force with Zero leakageValve shaft uses thrust bearings and "O" shaped seal ring to reduce friction, and stuffing box's leakage problem is also solved.

启闭力小，无外漏阀杆采用止推轴承和&O&型圈密封，减少了开关时的摩擦力，解决了填料箱漏水问题。

Friction locks cause throttle lever to stick.

摩擦锁导致油门杆不能移动。

Friction locks cause throttle lever to stick.

问推力杆锁锁定了推力位置，不能动。

P Friction locks cause throttle lever to stick.

问推力杆锁锁定了推力位置，不能动。

11P:Friction locks cause throttle lever to stick.

摩擦锁导致油门杆不能移动。