查询词典 forging

There is no hammer in my hand without the ecology of blacksmithing, steel forging, iron-mining, transportation and retailing.

没有一把锤子不是经过打造、金属锻造、矿石采取、运输和销售的生态网络才制造出来的。

I'm standing on the starting line to take over the relay baton companions, right next one board foot, straining the feeding effort, forging ahead and go!

我站在起跑线上，接过同伴的接力棒，右脚往后一登，使劲了吃奶的力气，往前冲去！

Of course, the human brain, with its 100 billion cells forging 1 quadrillion connections, is breathtakingly complex.

当然，人类的由100亿个细胞形成了1万亿个连接的大脑是惊人复杂的。

This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。

This design is to dials forks the components the processing craft and the jig design its components are the forging has the volume to be small components complex characteristicBecause the surface is easier than the hole to process when formulation technological process first the machined surface then processes other take the surface as the datumIn which various working procedures jig all uses the unit clamp special regarding processes the big end of hole the trough and drills the capitellum hole incline eyelet in the working procedure Chooses locate mode which two sells at the same time and operates the simple manual clamp way clamp its organization design is simple the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。关键词拨叉，加工工艺，专用夹具，设计

Hoist chain using low-alloy steel forging, and quenching by the carburization treatment, has a very high tensile strength and wear resistance.

提升机环链采用低合金钢锻造，并经渗碳淬火处理，具有极高的抗拉强度和耐磨性能。

Because the cautery is deep usually,it's hard to see the forging handiwork from surface.

由于腐蚀一般都比较深，因此从表面上很难看出锻打工艺。

The research on microstructure pattern and mechanical properties of the circular ring parts by liquid forging experiment under different specific pressures and casting temperature s were stated.

通过圆环零件的液态模锻成形实验，对在不同比压和浇铸温度条件下，锻件的微观组织形貌和力学性能进行了分析研究。

The research on microstructure pattern and mechanical properties of the circular ring parts by liquid forging experiment under different specific pressure s and casting temperatures were stated.

通过圆环零件的液态模锻成形实验，对在不同比压和浇铸温度条件下，锻件的微观组织形貌和力学性能进行了分析研究。

The research on microstructure pattern and mechanical properties of the circular ring parts by liquid forging experiment under different specific pressures and casting temperatures were stated.

通过圆环零件的液态模锻成形实验，对在不同比压和浇铸温度条件下，锻件的微观组织形貌和力学性能进行了分析研究。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。