查询词典 force-feeding

Based on the analysis of one type high-speed gas bearing working principle, the bearing diameter of axle static carrying force model was set up, and the relationship between bearing clearance gas flow rate, intensity of pressure and orifice radius were analyzed, along with the diameter of axle movement tracking under the centrifugal force in the low rotating speed was found.

在分析一类高速气浮轴承工作原理的基础上，建立其轴径轴承的静态承载力模型，并据此分析出轴承间隙中气体流量、压强与节流孔孔径间的相互关系，以及在低速运转下受离心力作用的轴径中心运动轨迹。

When the pressure is low, the role of Poppet head pressure sufficient to overcome the pressure regulator spring force, Poppet Head is closed at this time there is no pressure on the oil through the damping holes on the balance of the piston movement, so a balance piston, the next two cavity pressure equal, balanced piston under the action of the spring force gently on the top of the seat, pressure port and overflow port unreasonable.

当压力较低时，作用在提动头上的压力不足以克服调压弹簧力，提动头处于关闭状态，此时没有压力油通过平衡活塞上的阻尼孔流动，故平衡活塞上、下两腔压力相等，平衡活塞在弹簧力的作用下轻轻地顶在阀座上，压力口和溢流口不通。

The inside surface difference between flank-extrados and flank-intrados of any section of loop shell should induce the force difference when the loop shell under internal pressure. The force difference in ring shell can balance itself.

对于内压作用下的任何弯管，因为弯管中线上径向向外的管壁表面积均要比中线上径向向内的管壁表面积大，两者面积之差在同一内压作用下产生面积压力差。

The acting force keeps its balance with reacting force of spring, which decides the relative place of core and seat and controls the back of valve's pressure.

当阀后压力P2增加时。P2作用在顶盘上的作用力也随之增加。此时。顶盘的作用力大于弹簧的反作用力。

Research purposes:The paper gives an introduction to the additional force transfer mechanism of welded turnout on ballastless track,presents the calculation model for welded turnout on ballastless track, calculates additional force and deformation of welded turnout on ballastless track by FEM,the result is compared with ballast track.

研究目的：分析无砟轨道基础上无缝道岔的纵向力传递机理，建立无砟无缝道岔计算模型，采用有限单元法计算了无砟无缝道岔受力及变形，并与有砟轨道无缝道岔进行了对比分析，为无砟无缝道岔设计提供参考依据。

The basis of static, flat汇交system of forces, torque and couple Department of plane, plane general system of forces, center of gravity and centroid, the internal force and internal force diagram, tension and compression, torsion, bending, stress analysis and strength of the theory of the stability bar , the point of movement, the basic rigid-body movement, points of complex, rigid body planar motion, the movement of particle differential equations, dynamic general theorem, static and dynamic method.

静力学基础、平面汇交力系、力矩与平面力偶系、平面一般力系、重心和形心、内力和内力图、拉伸和压缩、扭转、弯曲、应力状态分析和强度理论、压杆的稳定性、点的运动、刚体的基本运动、点的复合运动、刚体的平面运动、质点的运动微分方程、动力学普遍定理、动静法。

After analyseing the force of all the component in the cam with Direct-Moving-roller follower, the conclusion is gained that radius of base circle not only influence the ability of sending force, but also influence the roller s continuous rolling .

对滚子直动从动件盘形凸轮机构各构件进行了受力分析后，得出基圆半径的大小不仅影响传力特性，还影响滚子是否能做连续滚动的结论。

First, the computation theory of the anti-sliding pile has been researched including interaction between the pile and tho landslide, the mechanical model of the pile and the calculation method of the internal force of the pile with prestressed anchor cable. Second, the internal force status, the mechanical computation model and the design method of the foundation beam with prestressed anchor cable have been analyzed. Finally, by the example, engineering instance and the geology mechanical model test, the main results and conclusions deduced from the thesis have been compared and validated.

论文首先对抗滑桩的相关设计计算理论进行了研究，包括抗滑桩与边坡岩土体的相互作用，抗滑桩的力学计算模型以及预应力锚索抗滑桩的内力计算方法；其次对预应力锚索地梁的受力状态、计算模型以及设计方法进行了分析研究：最后结合工程实例和地质力学模型试验对相关结论进行了分析比较、验证。

This paper makes a three-dimensions finite element analysis for connecting the rod of Beijing Jeep 212 Engine by using ANSYS structural software and obtains the circularity of big-headed cylinder under the acting of pre-screwing force and the stress contours and deformation contours under the acting of pre-screwing force and the condition of working.

应用ANSYS结构分析软件，对北京吉普212发动机连杆进行了三维有限元分析。得出了螺栓预紧力对连杆大头圆度的影响；预紧力与工作载荷共同作用下连杆的应力和变形云图，为进一步改进设计提供了理论依据

Base on this analysis, a method is designed to improve the measurement brake force precision and repetition in the brake tester. By choosing a suitable sampling number, applying signal processing and optimizing sampling rate, the braking force measurement had higher precision and repetition.

分析了国内目前常用的制动台力学特性，并在此基础上，讨论了提高制动台测量制动精度和重复性的方法，通过选取合适的当量点数、信号处理和优化的采样速度，使制动力测量有较高的精度和重复性

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。