查询词典 flow point

It is available to carry out numerical simulation and fluid dynamic analysis further. Based on Frozen-Rotor Approach and Rotor-Stator Approach, the numerical simulation was carried out in the centrifugal pump and the numerical results showed that the flow in the impeller and volute of centrifugal pump is periodically unsteady. Due to the interaction between impeller and volute the flow is characterized by pressure fluctuations and it is the strongest at impeller outlet and at the vicinity of the tongue. The unsteady pressure fluctuations are also one of the most important reasons to induce vibration and noise. Secondly, the flow field of the volute is characteristic of the vortex flow, and the vortex flow presents very complicated developing process which is creating, increasing and dissipating every now and then. All these lead to very large flow loss in the volute.

采用Frozen-Rotor冻结转子模式和Rotor-Stator滑移界面模式系统开展了不同工况下离心泵内叶轮与蜗壳耦合的定常和非定常流动研究，结果表明由于叶轮与蜗壳的干扰蜗壳进口周向流动的不均匀性是非常强烈的，特别是叶轮与蜗舌间的相互干扰最为强烈，一直影响到叶轮进口和蜗壳扩散管出口的流场；在蜗壳内整个流动是以旋涡形式向出口推进的，并随着包角的变化旋涡表现出十分复杂的产生、发展和耗散的演化过程，导致蜗壳内较大的流动损失。

Moreover, with the assistance of grey series forecasting model and the rule of the annual precipitation, the annual average precipitation, groundwater flow field, groundwater level and spring flow in the future under current exploitation circumstances were forecasted. If 2010 is a high flow year (guarantee ratio 20%), or median flow year (guarantee ratio 50%), or even low flow year (guarantee ratio 75%), the underground water level of Heilongdong spring in flood season will exceed 130 m, or reach 130 m, or even below 130 m, and the spring flow in flood season will exceed 10 m^3/s, 7 m^3/s, 5 m^3/s respectively.

以灰色序列预测模型为辅助手段，结合历年的降水规律，对未来现状开采条件下的年均降水量、地下水流场、水位及泉流量进行了不同保证率条件下的预测，若2010年为丰水年（保证率20%）、平水年（保证率50%）、枯水年（保证率75%，黑龙洞泉汛期地下水位标高分别为超过130m、达到130m、低于130m，汛期泉流量分别为超过10立方公尺/s、7立方公尺/s、5立方公尺/s。

According to the principle of the diameter of a circle corresponding to the right angle and the principle of short side for little angle in right triangle, projecting the initially-chosen point to the hyper-planes of the linear equation group in which every linear equation can be regarded as a hyper-plane and the projection points can be obtained. The initially-chosen point, and one arbitrary projection point, and the solution point are all on the surface of the relative hyper-geometry ball, therein-to, there is a projection point which is nearest to the solution point and it can be regarded as the next iterative initially-chosen point, so the solution problem of the linear equation group can be changed as an iterative problem of approaching the solution on the surface of a hyper-geometry ball.

根据直径对应的圆周角足直角以及直角三角形中短边对小角的原理进一步知道，当将初始点向线性方程组中各个方程所代表的超平面上投影得到投影点时，初始点和其任何一个投影点及方程组的解点都将位于一个相应的超球面上，其中必定存在一个投影点离问题解点的距离最短，即把该点作为下一次迭代的初始点，从而可将线性方程组求解的问题变成球面上逼近解点的迭代问题。

Thence in a southeasterly direction to Corner Point No. CP14 (X = 484 330, Y = 683 415); thence in a. northeasterly direction to Corner Point No. CP15 (X = 484 390, Y = 683 490); thence in a southeasterly direction to Corner Point No. CP16 (X = 484 415, Y = 683 470); thence in a southwesterly direction to Corner Point No. CP17 (X = 484 355, Y = 683 395); thence in a southeasterly direction to Corner Point No. CP18 (X = 484 430, Y = 683 335); thence in a southeasterly direction to Corner Point No. CP1, the point of beginning.

从该点起向东南延伸至隅角点CP14（X = 484 330，Y = 683 415）；从该点起向东北延伸至隅角点CP15（X = 484 390，Y = 683 490）；从该点起向东南延伸至隅角点CP16（X = 484 415，Y = 683 470）；从该点起向西南延伸至隅角点CP17（X = 484 355，Y = 683 395）；从该点起向东南延伸至隅角点CP18（X = 484 430，Y = 683 335）；从该点起向东南延伸至隅角点CP1。

Experiments of flow conductivity closure stress of typical propping agent are done, propping agent short-term flow conductivity alteration index is defined, by this, the relation between fissure short-term flow conductivity and closure stress, it is close to exponential relation. 4. Establishing the mathematical simulator of hydraulic fractured well's production in a steady state, finding the relation curve between dimensionless flow conductivity and fracture penetration coefficient by means of calculation and analyses, it is the basis of hydraulic fracture. 5. Expatiating the importance of optimized hydraulic fracturing design in reservoir engineering, advancing the optimizing design method, fracture dimension can be calculated easily when the physical parameters are known. 6. Production rate decline standard curve of vertical fractured wells is achieved by mathematical simulation, when the flow pressure is certain , by asymptotic analyze, this decline curve is close to exponential relation.

完成了国内外典型支撑剂的导流能力闭合应力影响实验，在数据分析中定义了支撑剂短期导流能力变异系数，并由此发现裂缝短期导流能力随闭合应力变化的近似符合指数关系式； 4 建立了一种水力压裂井稳态产能的数学模拟器，计算分析找到了最优无量纲导流能力与裂缝穿透比之间的新型关系曲线，它是水力压裂优化设计的基础； 5 阐述了水力压裂油藏工程优化设计的重要性，提出了优化设计方法，在已知支撑剂物性参数条件下可简洁计算最优裂缝尺寸； 6 数学模拟给出了垂直裂缝井产量递减标准曲线，在井底定压条件下通过渐近分析表明，该递减曲线满足指数关系式。

The paper conducts special analysis upon the current status of new product development in the Coco Palm Group, considering the characteristics and applicable conditions of three modes (sequent product development flow, stage-based product development flow and hopper-like product development flow) used in current product development flow, the paper establishes a new production development flow for the Coco Palm Group.

本文着重对椰树公司的新产品开发的现状进行了分析，并结合现今产品开发流程的三种模式（顺序式产品开发流程，阶段门式产品开发流程及漏斗式新产品开发流程）的特点和适用条件，构建了椰树公司新的产品开发流程。

In order to overcome the difficulties in measuring the flow rate of oil-water two-phase flow, the measurements of total mass flow rate, respective mass flow rate and real density of oil-water mixture with a double-U Coriolis flow meter were investigated.

针对油水两相流流量的测量难题，采用双U型Coriolis流量计对油水混合物的总质量流量、分相质量流量和真实密度进行了测量研究。

A systematic study of correlation between nose disturbances and evoluted behaviors of asymmetric vortices over slender body models has been conducted. The new flow phenomena have been revealed in which the two-cycle behavior of Cy vs.γ curve for asymmetric vortices flow is continuously changed into one-cycle behavior with increasing of disturbance strength on the model nose tip. This newly found flow phenomenon is important and it provides a physical flow base to the perturbation active control of forebody asymmetric vortices flow.

系统研究并获得了头部人工微扰动的形式、位置和强度与非对称涡响应演化之间的相关关系，揭示了前体非对称涡系随头部扰动强度的变化呈现出由双周期向单周期连续演化的新现象，它为实现前体非对称涡的扰动主动控制提供了流动的物理基础，以此提出了单孔位微吹气扰动主动控制新技术。

In general, the design work with traditional measures is done by hand, which cannot meet the needs of the technology and manufacture. So the author has developed a CAD hydraulic design software fit for lower specific speed axial flow runner, which is easily operated by users.The main research work of this paper is as follows:1 Analyzing the main reason of axial flow power station cannot work well under littler volume of flow in some season and putting forward an improving scheme, pointing out the characters of design under abnormal factors.2 Combined with the development of the industry in our country, the abnormal hydraulic design method of propeller turbine is discussed based on present literature, data and experiment results.3 Guided by the design method of software engineering, a suit of hydraulic design software of Lower Specific Speed Axial Flow Runner is programmed by the object-oriented programming language Visual Basic and a straightforward, concise and standard Windows human-computer dialogue interface is designed for the system, which makes the operation of the system very convenient.4 ActiveX Automation technology is adopted as the interface with AutoCAD and the hydraulic drawings are edited, modified by AutoCAD until hydraulic model drawings according with the demand of engineering practice are output.5 To resolve practice problem, the author has designed a lower specific speed axial flow runner for Duowa Power Station through an example.

论文的主要内容有：1 深入分析很多轴流定桨式水电站枯水季节小流量下不能发电的主要原因，提出减容改造方案，并指出超常规条件下的改造设计特点。2 结合国情及行业发展需要，参考现有资料、文献和前人的研究成果，进行低比转速轴流式转轮叶片水力设计方法的研究，对轴流式转轮叶片的奇点分布法水力设计进行了全面的探索，结合现代计算机技术，找到了一种针对特殊条件的轴流式转轮叶片水力设计方法。3 仔细比较多种AutoCAD二次开发工具后，结合本课题的特点，选用Visual Basic语言，综合应用软件工程的设计思想，进行低比转速轴流式转轮叶片水力设计软件的编制，为系统设计了直观、简洁和标准的Windows人机对话界面，便于用户操作；编程时在考虑到设计条件特殊性的同时，尽量做到程序的通用性，使之可用于解决同一类问题；另外，大部分程序还可移植到普通轴流式转轮叶片水力设计中，具有良好的适应性。4 利用ActiveX Automation技术与AutoCAD接口，对AutoCAD进行二次开发，在AutoCAD下实现水力图的自动生成和编辑，直至输出符合实际工程要求的木模图。5 通过算例，为多哇水电站设计了一个低比转速轴流定桨式转轮，解决其在枯水期小流量下不能发电的问题。

Besides, I also find that firms report negative earnings for fiscal year, which have less current and future earnings response coefficient than report positive earnings, and firms report negative cash flows from operating for fiscal year, which have less current cash flow response coefficient than report positive cash flows. Indicating that firms report negative earnings or cash flow, because losses are more transitory and which stock prices less information but which future cash flow response coefficient more than report positive cash flows. Inference of this study because cash flow have substance effect, so when firms have negative cash flows investor more care about it, which have more cash flow response coefficient, and further find while distinguishing the degree of sophisiticated investor, investor the sophisiticated degree proportion is higher. Because they know information of the earnings, firms have more degree of shareholder sophistication for fiscal year, which have more current and future earnings response coefficient than which have less.

此外，本文也发现报导损失之公司，其当期及未来盈余反应系数较报导利润之公司低，以及公司报导营业活动之现金流量为负时其当期营业活动之现金流量反应系数低於报导营业活动之现金流量为正之公司，显示公司报导损失或营业活动之现金流量为负时，因为通常都是暂时性的故其股票报酬的资讯性较低，不过其未来营业活动之现金流量反应系数高於报导营业活动之现金流量为正之公司，本研究推论因为现金流量是有实质的效果，所以当现金流量为负值时投资人应该会比较关注，所以其反应系数较高，而进一步发现当区分投资人之精明程度时，投资人精明程度比重较高，因其会辨识盈余资讯而认为公司进行损益平稳化会增加其资讯内涵，故当期及未来盈余反应系数相较於投资人精明程度较低者高。

The witness also told the jury at the Royal Courts of Justice in London that he saw a paparazzo fighting with a member of the public who was trying to stop him taking pictures in the minutes before the emergency services arrived.

他还告诉在伦敦皇家法庭的陪审团，在急救服务到来之前，他当时看见一个狗仔队正和一群阻止他拍照的人打架。

The entire N／C program on a tape is made up of an accumulation of these successive data blocks.

纸带上的整个数控程序由这些连续数据单元连接而成。