查询词典 flexural
- 与 flexural 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
energy method, flexural equation, trigonometric series equation, casing string flexural de-form, directional well
因此。文献[3]在此基础上,将套管柱当作既受横向荷载又受轴向力作用的梁来考虑,使套管柱的受力模式
-
Indoor flexural fatigue tests are carried out, the results are analyzed and two types of double logarithm fatigue equation under different stress level andequivalent stress level are got. Using the fatigue equation, the fatigue performance of porous concrete and common semi-rigid base materials and cement concrete are compared, the fatigue stress coefficient which is used in the load stress calculation for porous concrete as undersurface of cement concrete pavement and the tensile strength structure coefficient which is used in the flexural stress check for porous concrete as base of asphalt pavement are obtained.
进行室内小梁弯拉疲劳试验,对疲劳试验数据进行分析,得出多孔混凝土不同失效概率下两种形式的双对数疲劳方程,利用疲劳方程,将其疲劳性能与常用半刚性基层材料和水泥混凝土进行比较,还得出了多孔混凝土作为水泥混凝土路面下面层荷载应力计算的疲劳应力系数,和作为沥青路面基层层底弯拉应力验算的抗拉强度结构系数。
-
This paper proceeded the flexural experiment respectively of two flexural strengthen beam by CFS, one compared reinforced concrete beam, and proceed sheared experiment research of two U style stirrups of CFS combined compacted sheared strengthen beam, one compared reinforced concrete beam. analyze and compare some working characters such as width of cracks, the deflection and ultimate moment of an unstrengthen compared beam, an initial strengthen beam and a beam strengthened after crack by compacting .
本文分别进行了2根粘贴碳纤维布受弯加固梁和1根钢筋混凝土对照梁的受弯试验研究及2根碳纤维布U形箍+压条受剪加固梁和1根钢筋混凝土对照梁的受剪试验研究,分析对比了对照梁、直接加固梁、压裂卸荷后再加固梁三者的挠度、裂缝、极限荷载等工作性能。
-
Brick arch failure mode:Cracks are separated into shear and flexural cracks, the shear and flexural crack of un-reinforced brick arch occur in arch angle 63o respectively and at the bottom of 3rd brick walls on both sides of opening.
砖拱破坏模式:缝大致上可分为剪缝与挠曲缝;未补强砖拱斜向剪缝发生处为拱心角约63o 处,挠曲水平缝发生於开口侧底部三皮砖位置。
-
On the base of large amount of tests, this thesis analyzes the impacts of testing period, fiber dosage and cement dosage upon the compressive strength, splitting tensile strength, compressive resilient modulus, flexural strength and flexural elastic modulus of polypropylene fiber cement stabilized macadam, and the corresponding impact rule was found.
3在大量试验的基础上分析了试验龄期、纤维掺量、水泥掺量对聚丙烯纤维水泥稳定碎石抗压强度、劈裂抗拉强度、抗压回弹模量、抗弯拉强度和抗弯拉弹性模量等的影响,并得出了相应的影响规律。
-
When the depth increases, the displacement of wall and the flexural torque value reduce, but the change is small. So if the depth satisfied with soil body hardness and enclosure wall stability, to increase the depth is useless to displacement and flexural torque of wall.(3) Supporting severity.
围护墙的插入深度影响方面,墙的插入深度增加墙体变形和弯弯矩值减小但变化不大,因此当插入深度已经满足土体强度与围护墙的稳定时,再加上深度对墙体变形和弯矩作用影响不大。
-
The experimental results indicate that the flexural strength increases with the increase of the ratio of flexural reinforcement and the thickness of flange of the shape steel; the shear strength increases with the increase in the thickness of the web of the shape steel.
试验结果表明,箱形SRC梁的抗弯强度随纵筋配筋率和型钢翼缘板厚度的增大而提高,剪切强度随型钢腹板的厚度增大而提高。
-
The results show that: the tensile strength, flexural strength and flexural modulus increase by about 10.4%, 62.1% and 122.3% respectively when the mass fraction of the aluminum powder increases from 0 to 50%, while elongation at break and impact strength decrease by about 65.0 and 74.4% respectively; the tensile strength, elongation at break and impact strength all increase with decreasing the particle sizes of the aluminum powders.b Nylon-12 coated metal powders for the indirect SLS process were prepared by the dissolution precipitation process. The coated powders have only 1.0 wt% nylon-12, and their SLS green parts have sufficient strength for features as small as 1.0 mm to be built and post-processed and high dimensional accuracy. The green parts were subjected to the post processing processes including binder decomposition and infiltration of epoxy resin, and then the metal/polymer composite parts with relatively high strength and accuracy were formed.At present, micron-scale inorganic fillers have been widely used to reinforce nylon SLS parts.
将该法制备的尼龙12覆膜金属粉末用于以下两个方面:a使用铝粉增强尼龙12的SLS成形件,通过溶剂沉淀法制备尼龙12覆膜铝复合粉末,研究了铝粉含量及粒径对SLS成形件性能的影响,结果表明:铝粉分散均匀,并与基体有良好的界面粘接;当铝粉含量从0增加到50wt%时,成形件的拉伸强度、弯曲强度、弯曲模量分别提高10.4%、62.1%和122.3%,冲击强度和断裂伸长率下降65.0%和74.4%,耐热性及尺寸精度也得到提高;断裂伸长率、冲击强度及拉伸强度均随着铝粉粒径的减小而增大。b使用溶剂沉淀法制备了间接法SLS用尼龙12覆膜金属粉末,该覆膜粉末中聚合物粘接剂的含量仅为1.0 wt%,其SLS初始形坯具有较高的精度以及足够满足后处理要求的强度,最小精细结构的尺寸达1.0 mm。
-
In order to prevent wheat stem lodging and to fertilize precisely, the experiments on the influence of phosphate and potash fertilizers on mechanical properties of wheat stem were performed with Zhengzhou-wheat 9023 as an object. Mechanical properties (such as flexural strength and flexural rigidity) of second base inter-node were measured by six treatments at five growth stages of wheat, which were jointing stage, booting stage, flowering stage, grain-filling stage and maturity stage. Nonmetallic material testing machine was used in the experiments.
为了对小麦精准施肥,提高小麦的抗倒伏能力,该文以郑麦9023为研究对象,磷钾肥配施共6个处理,分别在小麦拔节期、孕穗期、扬花期、灌浆期、成熟期等5个生长期,利用非金属材料万能试验机,对去鞘茎秆作3点弯曲试验,测试茎秆基部第2节间的弯曲强度和抗弯刚度。
-
In designing the flexural reinforcement for the major moment for a particular beam for a particular section, the following steps are involved:· Determine the maximum factored moments · Determine the reinforcing steel Determine Factored Moments In the design of flexural reinforcement of moment resisting concrete beams, the factored moments for each load combination at a particular beam section are ob- tained by factoring the corresponding moments for different load cases with the corresponding load factors.
在设计一个特定部分,特别是梁为关键时刻抗弯增强,下面的步骤涉及:·确定时刻的最大因素·确定钢筋确定的因素时刻在目前的抗弯曲钢筋混凝土梁的设计,在特定的梁截面为每个荷载组合的因素是肥胖的时刻,由保理与相应的负载系数不同的负载情况下,不引起相应的时刻。
- 推荐网络例句
-
As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.
每逢看到沃林顿那刚毅的脸,那乌黑、忧郁的眼睛,她便会相信,他一定作过不幸的爱情的受害者。
-
Maybe they'll disappear into a pothole.
也许他们将在壶穴里消失
-
But because of its youthful corporate culture—most people are hustled out of the door in their mid-40s—it had no one to send.
但是因为该公司年轻的企业文化——大多数员工在40来岁的时候都被请出公司——一时间没有好的人选。