查询词典 flange

Level the body assembly until the short end of the bolt can also fit into the rocker panel hole (Figure 3). Tighten the flange nut, using a 24mm or 15/16 socket or wrench - the base will center the bolt.

校平主体总成，直到螺栓的较短一端也能配合进摆杆面板孔（图3）用24mm或15/16的套筒或扳手拧紧法兰的螺母－底座将对中心于螺栓。

Main various types of plastic extrusion machines, injection molding machines, chemical fiber spinning extruder, rubber tube extruder screw machine screw, Liao Tong, flange, such as printing network box.

主营各种型号的塑料挤出机、注塑机、化纤纺丝挤出机、橡胶挤出机机筒螺杆螺杆、料筒、法兰印花网框等。

After adjusting and installing with the spring balance bring 20-40N ( as illustrated in figure 3) to bear on bolt hole in the small gear hub, the flange should be able to turn.

调完安装好后，用弹簧秤在小齿轮壳螺栓孔处施以20－40N 的力（如图3），应能转动突缘。

With 3.0 t empty dual-use steam forging hammer, 1.0 t empty dual-use steam forging hammer, 750 kg, 400kg, 250kg, 150kg Kong Qichui a total of seven, made 3.0 t, 2.5t of a hammer plywood Taiwan, the construction of 2 m × 1.5m × 1.0m two large coal-fired furnace, a gas generator furnace, resistance furnace, Oil Furnace, Meilu stoves and other heat treatment of the four sets, with the following specs for Φ550 Saw 5,φ100 major fault Liu and other supporting material under the equipment, and has CW611250, T68, and other machining equipment, more than 60 species of vehicles, milling, planing, grinding, boring jobs complete, the main products φ820 × 60 × 1300 following the suppression of three products,φ273 high-pressure forging Billet-three links, all kinds of high-pressure-welded flange and 3.0 t following forging free, annual production capacity of 2400 t.

拥有3.0t空蒸两用模锻锤，1.0t空蒸两用模锻锤，750kg、400kg、250kg、150kg空气锤共7台，自制3.0t、2.5t夹板锤各1台，建造2m×1.5m×1.0m大型燃煤加热炉两座，煤气发生器加热炉1座，电阻炉、油炉、煤炉等热处理炉具各4套，拥有加工规格为Φ550以下锯床5台，φ100大型断料机等配套下料设备，且拥有CW611250、 T68等机加工设备60余种，车、铣、刨、磨、镗工种齐全，主要产品φ820×60×1300以下压制三通成品管，φ273高压锻制三通方坯，各种中高压平对焊法兰及3.0t以下自由锻件，年生产能力2400t。

Our company has kinds of standards such as ASME、ANSI、DIN、JIS、GB、SH、HG、JB and has various of forging that apply in producing forging steeliness flange and pressure vessl of kinds of materials(carbon steel,alloy steel,low temperature steel and stainless,etc.).

我公司有国内外各种标准（ASME、ANSI、DIN、JIS、GB、SH、HG、JB等），生产各种材质（碳钢、合金钢、低温钢、不锈钢等）的锻造钢制法兰、船舶类锻件及各种压力容器用锻件。

The distribution mode of bond stress is noted on the flange and the web of structural steel.

提出了型钢翼缘和腹板处的粘结应力分布模式和极限粘结强度的算法。

Elongation type valve cover: one valve cover, stuffing box and the distance between the valve cover flange is longer, for high or low temperature conditions.

伸长型阀盖：一种阀盖，填料函与阀盖法兰之间的距离较长，用于高温或低温工况。

Stylopodium depressed, margins conspicuously extended into a broad undulate flange.

花柱基下凹的，边显著延伸成一宽的波形凸缘。

3 Gasket contact surface of girth flange shall have a finish equivalent to the following in μm.

同法兰表面接触的垫片的磨光应符合下列要求，单位μm

Then the radial and tangential stress at any point of the deformation area have been deduced when the flange radius is certain according to the equilibrium differential equation.

利用应力应变关系对翻边终了时孔的边缘切向拉应变作推导。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。