查询词典 fixed load

The operation staff should test all the running parts, connection, fixed parts, track and wire rope, etc. everyday before operate the machine, then vacancy load for 3 times to confirm reliable. When using it ,pay attention to the conditions of hoisting machine, sliding wheel, wire rope, hang coop. Make

6.5操作人员应在每天操作前检查各运行部分，各连接，固定部位、轨道及钢丝绳，无异常情况，然后，操作运行空载上下三次，确认安全可靠后，方可使用，使用中要随时注意卷扬机记录，下班时检查各部件，并清扫吊笼内灰渣，锁好护栏门，将总电源关闭

During the experiment, we choose Toyota Corona 1600cc as a test car and measure its maximal acceleration value by means of palm vibration noise analyzer, on conditions of the same tire pressure, speed, load, and road section and measure fuel consumption in a fixed speed and mileage. In addition, by using tire pressure gauge and infrared thermometer, measure after-driving tire pressure and tire temperature to make a comparative analysis. Finally, we use 185/60 R-14 Goodyear tire to measure tire sinkage in an empty car and a loaded car and obtain tire compression ratio to explain the difference of riding comfort and economical consideration of fuel consumption between nitrogen-filled tires and compressed air tires.

在实验时，采用丰田Corona 1600cc轿车，在相同的胎压、车速、负载、路段等条件下，透过掌上型振动噪音分析仪，撷取车辆行驶之最大峰值加速度；并在稳定车速及固定里程下量测汽油之消耗量，再以胎压表和红外线温度计，量取行驶后之胎压和胎温值来作比较分析，最后，再使用185/60 R-14 Goodyear 轮胎，在车上量测空车及负载下轮胎的下沉量，并求得轮胎的压缩率变化值，来说明氮气轮胎与一般压缩空气轮胎，在乘坐舒适性及燃油经济性上的差异原因。

As we know, support at the both straight edge of ACMR is a elastic support between the hinged support and fixed support, and its stiffness is variational. So the relation between support stiffness and load-carrying capability of ACMR is worth to be studied. Meanwhile, arched roof is generally set on beam at the top of pillar.

众所周知，实际工程中波纹拱两端的直边支座处于铰支和固支之间，属一弹性支座，其弹性刚度是变化的，支座刚度与波纹拱结构受力性能及稳定承载力之间的关系是一个非常值得研究的课题。

Traditional plastic injection molding machine relies on constant rate pump in oil supply, and each action in the process of plastic injection may have different requirements on speed and pressure. The surplus oil flows back to the oil tank through the proportioning valve in the way of flooding adjustment. In the whole process, the rotation speed of motor remains unchanged, so the oil volume is fixed as well. Furthermore, the action is intermittent, and not of full load, so a great amount of oil is wasted.

传统的注塑机是采用定量泵供油的，注塑过程的各个动作对速度、压力的要求也不一样，它是通过注塑机的比例阀采用溢流调节的方式将多余的油旁路流回油箱，在整个过程中，电机的转速是不变的，故供油量也是固定的，而由于执行动作是间隙性的，也并不可能是满负载的，因此定量供油就有很大的浪费空间。

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国，慢性酒精中毒，肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题，你可以随时联系我。