查询词典 fixed element

This bug is easily fixed by setting the display property of the element to inline. As the element

这个bug 很容易修复，将元素的display 属性设置为jnllne 就行了。

Second order incident boundary condition on fixed incident boundary is derived for numerical simulations, based on the cnoidal or sinusoidal motions of wave maker paddle, which shows that the prediction with second order incident boundary condition is more accurate than the prediction with first order incident boundary condition. 2 The analytical solution for higher-order Boussinesq equations is derived and its applicable range is discussed. 3 A 2-D fully non-linear numerical model using boundary element method is developed to obtain wave forces acting on rectangular obstacle. 4 The three-dimensional fully non-linear waves are studied in a numerical wave tank using finite element method.The studies on the coupled numerical model combined Boussinesq equations with Laplace equation are following.

非耦合非线性波浪计算模型：1 根据造波板做椭圆余弦运动或正弦运动速度，推导出数值模拟波浪水槽时固定入射边界上的二阶波浪入射边界条件，数值计算结果和实验结果的对比表明采用二阶入射边界条件对波面升高的预报比采用一阶入射边界条件对波面升高的预报更为精确；2 推导了波浪水槽造波板做正弦运动所产生波浪的高阶Boussinesq方程摄动展开解析解，讨论了该解析解的适用范围；3 对整个波浪水槽应用边界元方法数值模拟了波浪对物体的非线性作用；4 用有限元法求解三维Laplace方程模拟了三维完全非线性波浪水槽。

A drive shaft member extends from the movable base element through the fixed mounting element and beyond.

从可移动的基体件延伸的驱动轴穿过并超过固定的固定件。

A spring member, such as two planar leaf springs positioned at an angle to each other, is mounted between the movable base element and the fixed mounting element.

弹性件，如两个互相定位成一定角度的平面板簧，安装在移动的基体件和固定的固定件之间。

In order to acquire the spatial stress distribution of the pier-beam fixed joint , a pier-beam fixed joint finite element space model is established and analyzed in different loading cases.

为掌握石板坡大桥墩梁固结点的三维应力状态，建立了墩梁固结点结构分析的空间有限元模型，根据施工过程中及成桥后的工况，分别进行了空间有限元计算，得到了墩梁固结点在三种工况下的应力分布情况，检验了设计的安全性与合理性，提出了改善墩梁固结点应力的措施和方法，为设计和施工提供了科学的依据。

Based on a fixed grid finite element framework, a novel bi-directionalevolutionary optimization technique, namely FG BESO, is presented to generatesmoother boundary in fixed grid shape design.

推导了基于固定网格用于评价开孔应力集中水平的等Tsai-Hill值敏感度指标，研究了复合材料板壳结构开孔形状优化问题。

The modal tests of PCB and PCB assembly (free boundary condition and fixed boundary condition) were carried out. The equivalent elastic modulus and damping parameters of PCB can be gained, and the fixed boundary condition of finite element model was also determined. These will help to the following work.Second, drop impact tests of three different heights were carried out. Strains and acceleration responses of PCB were measured. Failed BGA packages of different test conditions were dyeing, and cross section analysis of failed solder joints was conducted.

针对JEDEC标准试件的局限性，提出了设计便于统计学研究焊点可靠性的试验试件的构想，利用有限元模态分析方法确定并验证了用圆形PCB组件替代JEDEC标准试件的可行性；通过一系列模态试验和有限元模态分析，确定了圆形PCB组件的相关试验参数，这不仅为跌落碰撞下PCB组件有限元模拟确定了较为合理准确的有限元模型，而且为正确地评价跌落碰撞下PCB组件的可靠性问题奠定了基础。2。

The apparatus for converting side-to-side to rotational motion for a workpiece includes a spring assembly with a movable base mounting element which is driven in a slightly arcuate reciprocal side-to-side motion and a fixed mounting element spaced apart from the base element and mounted in the appliance so that it does not rotate or move in operation of the apparatus.

一种将工作件的侧向运动转换为旋转运动的装置，包括弹性组件，带有作微小弧线往复侧向移动的可移动的基体固定件，和与基体件间隔开的固定的固定件，其固定在器具上在器具操作时不会转动或移动。

The modal tests of PCB and PCB assembly (free boundary condition and fixed boundary condition) were carried out. The equivalent elastic modulus and damping parameters of PCB can be gained, and the fixed boundary condition of finite element model was also determined. These will help to the following work. Second, drop impact tests of three different heights were carried out. Strains and acceleration responses of PCB were measured. Failed BGA packages of different test conditions were dyeing, and cross section analysis of failed solder joints was conducted. It was found in our drop tests that the root cause of lead-free solder joints under drop impact was the combined effect of mechanical shock and PCB bending vibration.

针对JEDEC标准试件的局限性，提出了设计便于统计学研究焊点可靠性的试验试件的构想，利用有限元模态分析方法确定并验证了用圆形PCB组件替代JEDEC标准试件的可行性；通过一系列模态试验和有限元模态分析，确定了圆形PCB组件的相关试验参数，这不仅为跌落碰撞下PCB组件有限元模拟确定了较为合理准确的有限元模型，而且为正确地评价跌落碰撞下PCB组件的可靠性问题奠定了基础。

Heat transfer model was analyzed for polishing with ice fixed abrasives in this paper. With ANSYS finite element, the value of temperature fields for polishing was simulated. The temperature contour map of temperature field and the melting thickness values of working area of ice fixed abrasive tool were obtained. Polishing experiments were conducted with the same technological parameters.

本文分析了低温固结磨料抛光硅片的传热模型，并借助有限元软件ANSYS对热传导过程进行了仿真，获得了冰冻磨具在不同抛光时刻的温度场等温图及工作区域的融化厚度值。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。