查询词典 finite

New progresses in finite element analysis for telescopic box section hoist boom of truck cranes are summarized. Merits and defects of existing finite element methods arc analyzed.

总结汽车起重机箱形伸缩式吊臂有限元分析国内新进展，分析现有的有限元方法优缺点。

Considering the loading and boundary conditions of the model finite element calculation is carried out. Both for the working conditions of prestress and load, the finite element model of the box beam is approved to be suitable and correct by the actual test results.

考虑模型的载荷及约束进行有限元计算，在预应力和载荷两种工况下，利用实测结果论证了箱型梁的有限元分析模型是合适和准确的。

A finite element modeling and analysis of the assembly of a breech mechanism in locking condition was carried out with special finite element techniques such as contact element, gap element and spring element.

利用接触元、间隙元和弹簧元特殊单元，对某大口径火炮的炮尾-闩体-曲臂机构进行了闭锁状态下装配体有限元建模和分析。

The finite element analysis model of pre-pressing contact of low carbon steel resistance spot welding un-der spherical electrode condition is created with the finite element software.

1前言电阻点焊是汽车制造领域中的主导加工工艺，每辆汽车上的电阻焊点平均为3000～5000个[1]，因此电阻点焊的质量很大程度上影响着汽车的质量。

To this end, a numerical approach combined by the finite element method for magnetic fields and the finite difference method for deflection of the microsensor is proposed to analyze quantitatively the deflection under magnetoelastic interaction.

为此，建立了由有限元方法分析磁场与有限差分法计算挠曲变形相结合来计算其结构在磁场中产生磁弹性变形的定量分析程序。

In this paper,the authoruses the method of the explicit finite-element numerical simulation, which isbased on the most simple two-dimensional-finite-element modle and kinematicsource model,to study the basic characteristics of near-fault ground motion, suchas the changing tendency of the hanging-wall effect and the vertical effect as weonly change the fault dip or the depth of the top of the fault.

本文拟利用最简单的二维有限单元模型和基于有限断层假定的震源运动学模型，采用集中质量显式有限元数值模拟的方法研究近断层地震动的特征，如上盘效应和竖向效应随断层倾角以及断层的上界埋深的变化而改变的趋势。

First, the stretch tests of polyester samples were carried out according to the test methods required by the corresponding national standard, from which the coefficients for Mooney Rivlin equation were achieved; then the finite element models of the standard test samples and dust cap were established, and the nonlinear finite element software MSC-Marc was used to calculate the their stiffness.

首先，根据橡胶产品的国家标准进行标准试样的拉伸试验，由此得到有限元模型中材料模型的参数；然后，建立相应的标准试样和聚酯防尘罩产品的有限元模型，并通过非线性有限元软件MSC-Marc进行了计算，得到标准试样和聚酯防尘罩产品的刚度。

Earlier fatigue failure phenomenon of SOFIM engine connecting rod bolt is concentred.After a finite element model was established,a finite element analysis and a fatigue test were carried out.

针对SOFIM发动机连杆螺栓出现的早期疲劳断裂现象，建立了连杆螺栓的有限元模型，利用有限元方法进行了该连杆螺栓的疲劳寿命分析，并与疲劳试验进行了对比。

Finite element method is based on the actual ship models, a true reflection of the real ship distribution of the specific structure. This paper also uses empirical formula to calculate the inherent frequency of the catamaran; contrast them in the process of modeling the structural stiffness, and quality of the different treatments, as well as natural frequency calculated from the results of differences analyze the different and the reason between the finite method and the empirical formula method which used to calculate the inherent frequency of catamarans in the vibration analysis.

有限元方法是根据实际船型，较真实的反映了实船结构的具体分布特征；本文还采用经验公式对该船的固有频率进行了计算，对比它们在建模过程中对结构刚度、质量的不同处理，以及计算所得固有频率结果的差异，分析了在双体船振动特性分析中有限元法与经验公式法的结果略有差距及其原因。

In this dissertation the"Penalty"finite element method was employed to compute the velocity of the three-dimensional flow of power-law fluid in a profile die. In order to decrease the needed computer memory and raise the stability of numerical simulation, a set of decoupled methods such as PFEM, pseudo-body force method and transformation of momentum equation to the elliptic equation was developed to establish the general finite element equations to compute the distributions of velocity and viscoelastic stress of the three-dimensional viscoelastic flow of the Phan ThienTanner fluid in a profile die. During numerical simulation of the extrudate swell of the PTT fluid, the flow in the die and out of the die was analyzed separately, which demands less computer memory.

本文建立了求解挤出口模内幂律流体流动速度场的通用三维罚有限元模型；对于非线性粘弹性的Phan Thien-Tanner流体，为了降低模拟计算对计算机硬件的要求，并使模拟计算更加稳定，采用了一种去耦算法，包括罚有限元方法、拟体力方法和动量方程的椭圆类方程转化方法，并建立了求解速度场和粘弹性应力场的总体有限元方程；对于PTT流体的挤出胀大问题，提出了挤出胀大熔体口模内外分离模拟法，这样可以显著降低数值模拟对计算机硬件的要求。

Now she was hungry and angry.She began to smoulder.

现在她又饿又气，她开始流露难以抑制的怒火。

You have placed our iniquities before You, Our secret sins in the light of Your presence.

诗90：8 你将我们的罪孽摆在你面前、将我们的隐恶摆在你面光之中。