查询词典 filler

The trifunctional polyhydric alcohol is more, the elasticity coefficient and surface hardness are higher. 2. Catalyst. The appropriate dosage of catalyst is determinated. To N-330, it is 0.15%; to N-220, it is 0.35%. 3. Filler. The more the solid filler is, the higher the properties of polyurethane elastomer are. The effect of liquid filler is more perplexing.

结果表明：三官能度聚醚含量增加，试样的弹性系数和表面硬度随之增大；固体填料含量增加，试样的弹性系数和表面硬度随之增大，液体填料的影响较为复杂；催化剂辛酸亚锡的合适用量为0.15%(N-330)或0.35%(N-220)。

This Paper has discussed the Properties of the calendered mettalic porous corrugated sheet filler, and the effects of using this corrugated sheet filler in the fatty acids distillation process, It suggests to set up a research topic on the problem to use this special corrugated sheet filler in the absorption of the end gas in tne oil extraction plant and indicates its gratifying possibility.

本文介绍了金属压延孔板波填料的特性，以及在脂肪酸精馏技术应用中的效果。提出了在油脂浸出尾气吸收工艺中，应用金属压延孔板波填料的研究课题及可能性。

In addition, the repair method can also be filled tree holes, stuffing is best to use small gravel and cement mixture to be compacted filler, filler to strengthen the connection with the xylem, inside the cave can be a number of electroplating nails nails, holes dug in on both sides 4 centimeters deep groove at the bottom of filler from the start, each 20-25 cm for the layer, using linoleum separated from each floor should be inclined slightly outward to facilitate drainage, the edge should not exceed xylem, so that cambium in the formation of callus on it.

另外，也可用填充法修补树洞，填充物最好用小石砾和水泥的混合物，填充物必须压实，为加强填料与木质部的连接，洞内可钉若干电镀铁钉，洞口内两侧挖4厘米深的凹槽，填充物从底部开始，每20厘米至25厘米为一层，用油毡隔开，每层都要向外略斜，以利排水，边缘应不超过木质部，使形成层能在它上面形成愈伤组织。

After looking up a large amount of native and foreign information, the materials used in the experiment were as follows: PTFE base, graphite filler, molybdenum disulfide filler, copper powder filler, carbon fiber and so on. The experimental method is that the formula was designed according to uniform experimental method, the relationship between formula and frictional property was found with spline function and then the representative test points were chosen from fitting curve to make verification test for optimization.

经过查阅大量国内外文献资料后确定原料为：聚四氟乙烯树脂为基体，加入石墨、二硫化钼、铜粉、碳纤维等填料；试验方法为：根据均匀试验方法设计配方，用样条函数找出配方与摩擦性能的关系，然后在拟合曲线上选取具有代表性的试验点进行验证试验，达到优化的目的；制备工艺：冷压烧结法制备固体润滑剂。

Aiming at filler wall quality problems,it analyzes the chief origins of the filler wall crack,brings forward corresponding prevention measures,overcomes the filler wall crack quality control problems basic with the reinforced management in construction,and increase the quality requests of housing.

针对填充墙体的质量问题，分析了填充墙体产生裂缝的主要原因，提出了相应的防治措施，并在施工中加强管理，基本克服了填充墙体裂缝的质量控制难题，提高了住宅楼的质量要求。

Ti element is found to aggregate, forming an ultra-fine reaction layer in the active filler metal-ceramic joint after 260℃/24hr aging treatment. Two different-color intermetallic compounds are observed in the interface of active filler metal-copper. One is Cu6Sn5 , which is closer to active filler metals;the other is Cu3Sn, which is closer to the copper substrate.

接合后之试片，经260℃/24hr时效反应后，发现Ti元素聚集於焊料与陶瓷界面处形成一层极薄的反应层且发现在焊料与铜之反应界面有了明显颜色不同之两层介金属层生成，靠近焊料端的介金属层为Cu6Sn5，Cu片端的是Cu3Sn；而Cu6Sn5化合物从原本未时效10μm成长为25μm。

Old naphthalene removing filler is easier jam. But new porous light porcelain structured filler has beyond comparison excellence to wood grille filler. It can enlarge fourfold adsorption surface, greatly promote naphthalene removing effect, increase purification efficiency and insure the quality of civil coke oven gas.

老式脱萘填料比较容易堵塞，新型多孔轻瓷填料有着木格栅填料所无法比拟的优点，能够在相同的重量下扩大四倍的吸附面积，极大的促进了脱萘液的脱萘效果，提高了洗萘塔的净化效率，确保了民用焦炉煤气的质量。

Nuclear connection:Fill SA Non-traumatic filler material in the teeth and Non_traumatic nuclear area,try your best to fit the shape of the filler,especially for the embrasure.

核连接：将SA无极填充材料均匀地填于牙齿和无极核的连接区，尽量修整好充填物的形态，尤其是邻牙间外展隙区应尽量修整美观自然。

Effect of active filler on joining property of silicon carbide to itself by polysilazane;2. The design,cross-linking and pyrolysis of preceramic polymers as well as addition of active filler ,all of which influence the ceramic yield,were analyzed.

针对先驱体转化法陶瓷产率低的问题，从陶瓷先驱体的设计、先驱体的交联工艺、裂解工艺以及活性填料的添加等方面分析了影响陶瓷产率的各种因素，总结出提高陶瓷产率的措施，最后提出今后进一步研究的方向。

Al and SiC powders were chosen as active filler and inert filler, respectively, for the fabrication of preceramic-derived multi-phased ceramics, using polycarbosilane as preceramic precursor.

采用微米级Al粉作为活性填料， SiC微粉作为惰性填料，聚碳硅烷作为陶瓷前驱体制备SiC基复相陶瓷。

Hanna: That's over now, isn't it?

都结束了，对吗

You must be ill. You look so pale.

你一定是病了，你的脸色苍白。