查询词典 feeler

A Mercedes tool kit with a few extras like a feeler gauge, spoke wrench, a file, a couple of jack knives, one of which is a Swiss Army knife, Chinese plug wrench, this means I have at least four ways to remove a plug.

奔驰工具包有一些额外像触角衡量，以扳手，一个文件，一对夫妇的杰克刀，其中之一是瑞士军刀，中文插件扳手，这意味着我已经至少有四种方法可以删除插件。

In implementation, a feeler gauge measures the thickness of the just-made sheet metal and sends this signal back to a servo-motor controlling the single variable of traction, the variable to affect the steel last, just before the rollers.

在实施过程中，由一个厚薄规测量刚刚制成的金属板的厚度，然后把信号传回一个伺服电动机以控制牵引力的单一变量——在卷板机之前最后影响钢板的变量。

5 Check immediately after installation with a feeler gauge if the rubber ring is in the desired position all around the circumference, that it is well inside the bell "lead in", and that the pipe is nearly fully home.

安装后应立即用塞尺沿着管道周长检查橡胶圈是否处在安装位置，如果橡胶圈在喇叭口的&插入&位置，那么管道基本上就安装就位了。

In implementation, a feeler gauge measures the thickness of the just-made sheet metal and sends this signal back to a servo-motor controlling the single variable of traction, the variable to affect the steel last, just before the rollers.

在设立这些反馈装置的时候，是有一个用来进行感觉的量器来测量刚刚作出的金属板的厚度，然后把这个信号传送回某种补助马达，这个补助马达控制的是一个单一变量，也就是牵引力——这个变量是最后影响钢板的因素，就在卷板机之前。

In implementation, a feeler gauge measures the thickness of the just-made sheet metal and sends this signal back to a servo-motor controlling the single variable of traction, the variable to affect the steel last, just before the rollers.

在设立这些反馈装置的时候，是有一个厚薄规来测量刚刚作出的金属板的厚度，然后把这个信号传送回某种伺服电动机上，这个伺服电动机是用来控制一个单一变量，也就是牵引力——这个变量是在卷板机之前最后影响钢板的因素。

Use nonmagnetic feeler gauge.

使用非磁性测隙规

Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm. Repeat it for three release levers, their gaps should be the same, after that screw up the locking nuts, and check it to make sure.

b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍。

B. Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm.

b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。