查询词典 feeler gauge

If you still have the lawnmower manual and a feeler gauge you can adjust the gap to the specifications.

如果您仍然有割草机手册和触角衡量您可以随时调整的差距，以规格。

Traditional method detecting by dial indicator or feeler gauge needs more time and effort.

传统的检测方法是由百分表或触角衡量，需要更多的时间和精力。

When new spark plug is used or after the sidecar has been driven for 1000 km,spark plug gap should be checked with feeler gauge.

当新的火花塞使用或之后的边门一直驱动为1000公里，火花塞间隙应检查与触角gauge。

Remedy: Check valve actuator with feeler gauge; re-adjust if necessary.

检查电子管驱动部分，若有需要重新调整

If valve clearance needs to be adjusted, loosen the locknut on rocker arm adjusting screw. Turn adjusting screw until feeler gauge slips with a slight drag.

如果气门间隙需要调节，松开摇臂调节螺丝上的防松螺母，转动调节螺丝直到测隙规滑动时稍带阻力为止。

Must cause the damper plate and the floodgate frame tallies, inspects the top and bottom packing surface with the feeler gauge the gap, makes the gap to maintain in 0.1mm, when gap exceeding the allowed figure, may the pad enter the slanting iron at the back of this place floodgate frame, simultaneously

需使闸板与闸框吻合，用塞尺检查上、下密封面的间隙，使间隙保持在0.1mm以内，间隙超标时，可在该处的闸框背面垫入斜铁，同时将膨胀螺栓略为旋松，直至间隙合格为止。

A Mercedes tool kit with a few extras like a feeler gauge, spoke wrench, a file, a couple of jack knives, one of which is a Swiss Army knife, Chinese plug wrench, this means I have at least four ways to remove a plug.

奔驰工具包有一些额外像触角衡量，以扳手，一个文件，一对夫妇的杰克刀，其中之一是瑞士军刀，中文插件扳手，这意味着我已经至少有四种方法可以删除插件。

In implementation, a feeler gauge measures the thickness of the just-made sheet metal and sends this signal back to a servo-motor controlling the single variable of traction, the variable to affect the steel last, just before the rollers.

在实施过程中，由一个厚薄规测量刚刚制成的金属板的厚度，然后把信号传回一个伺服电动机以控制牵引力的单一变量——在卷板机之前最后影响钢板的变量。

5 Check immediately after installation with a feeler gauge if the rubber ring is in the desired position all around the circumference, that it is well inside the bell "lead in", and that the pipe is nearly fully home.

安装后应立即用塞尺沿着管道周长检查橡胶圈是否处在安装位置，如果橡胶圈在喇叭口的&插入&位置，那么管道基本上就安装就位了。

In implementation, a feeler gauge measures the thickness of the just-made sheet metal and sends this signal back to a servo-motor controlling the single variable of traction, the variable to affect the steel last, just before the rollers.

在设立这些反馈装置的时候，是有一个用来进行感觉的量器来测量刚刚作出的金属板的厚度，然后把这个信号传送回某种补助马达，这个补助马达控制的是一个单一变量，也就是牵引力——这个变量是最后影响钢板的因素，就在卷板机之前。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。