查询词典 feeding

Calves were divided in four groups, group MR1, MR2 and MR3 feeding milk replacers containing 60%, 70% and 80% of crude protein as vegetable protein respectively, group CK feeding whole milk as control group.

试验组MR1、MR2、MR3分别饲喂60%、70%、80%3种不同植物蛋白含量的代乳粉，对照组CK饲喂鲜奶，研究不同植物蛋白含量的代乳粉对断奶犊牛消化道主要消化酶活性的影响。

This book helps parents with everything they need to know about feeding babies during the first three years---including breastfeeding, bottle-feeding, pureed baby food, and solids---making it the most comprehensive baby nutrition book on the market.

中文概要：这本书帮父母了解在头三年该如何喂养宝宝——包括母乳喂养，纯婴儿食品和固体食品等，这些使这本书成为市场上婴儿营养书籍概括最为综合全面的书籍。

Cold state pure air resistance leveling method is broadly used in the feeding pipings of utility boilers' pulverized coal preparaption system.Such leveling method can not ensure resistance equilibrium among the pulverized coal feeding pipings during the boiler actual operation.

电站锅炉制粉系统送粉管道中广泛采用冷态纯空气阻力调平方法，在纯空气条件下的阻力调平不能保证锅炉实际运行时各送粉管道间的阻力平衡。

The content of poultry science is mainly composed of introduction, poultry breeding, reproduction and hatch, as well as nutrition and management for feeding, environment control, equipments for poultry farm and technology for feeding, etc.

家禽学的主要内容为：绪论、家禽的育种、繁殖、孵化；营养与饲养管理；家禽的环境、禽舍与设备及各阶段的饲养管理技术等。

The universal powder box includes one box with powder bin and cover, one stirrer inside the powder bin, one powder feeding roller in the outlet of the powder bin, one developing roller contacting with the powder feeding roller and one locking device for the powder box to be set in and taken out from the sensitive drum. The cover has one upper planar surface, and after being installed, the plane is located below one corresponding raised edge of the printer. In the roller end gear combination outside one side wall of the box, there are two with driving force driving position.

包括一个带有粉仓的盒体和盖，位于粉仓内的搅拌装置，一个位于粉仓出口处的送粉辊、一个与送粉辊接触的显影辊，及使粉盒能顺利置入或取出感光鼓盒的锁放装置，盖的上表面基本是一个平面，装机后该平面位于打印机对应盖下表面凸起的下缘之下，在盒体一个侧壁外的各辊端齿轮组中，有两个带有动力受口的驱动位。

After the yolk bag of the inside goldfish fry body disappeared, the feeding should be starting with yolk water (50g egg yolk:5kg water ratio) by twice feeding daily.

4当鱼苗体内卵黄囊消失后，即可餵饲卵黄水（50g蛋黄调5kg水比例），通常每天上、下午各一次。

Compared the voltage negative feedback wire-feeding speed regulation system supported by current positive feedback with the rotational speed negative feedback regulation system, the equivalent condition of the two systems is obtained. Then, a wire-feeding speed regulation circuit for the CO_2 welding machine is designed based on TL494 chip, which has the self-protective function under the condition of current overloading.

通过对电压负反馈配合电流正反馈的送丝调速系统与转速负反馈调速系统的比较，得出了这两种调速系统的等效条件，并采用电压负反馈配合电流正反馈技术，设计了一种以TL494为核心的具有过电流截止保护功能的CO_2焊机送丝调速电路。

In this system the motion controlling centers upon regulating the speed of wire feeding and movement of lead screw in each direction.Four motors separately drive the wire-feeding tape roll and the lead screw move respectively following their directions of X, Y, Z axis. If all the motors are controlled by 89C51 directly,it will rise great difficulty for software and hardware implementation. So the suggested solution is to combine the microcomputer with stepper motor driver and control of their motion.

在本系统中运动控制的关键即送丝与各丝杠移动的调节，由四个电机分别驱动X，Y，Z轴方向的丝杠行走以及送丝操作，运动控制部分如果用89C51直接驱动各电机则在软件和硬件实现上都比较困难的，所以选用单片机与步进电机驱动器结合起来控制它们的运动。

To deal with the three-position mode. that is, a heat treatment spaces, spaces in the two months to feed silk processing, column electrodes three major equipment including : heating system, Ladle low argon blowing system, feeding cropping system, two ladle car. three wire-feeding machines and confiscated a slag.

处理模式为三工位，即一个加热处理位，俩个喂丝处理位，主要设备包括：三位立柱电极加热系统、钢包氩气低吹系统、上料下料系统、两台钢包车、三台喂丝机及一台扒渣机。

The relationships between welding pool width, wire extension and welding parameters including welding current duty ratio, base current, peak current, welding speed and wire-feeding speed were studied. Through large numbers of welding experiments, aluminum alloy pulsed MIG welding dynamic process were identified by the curve fitting method, and the mathematical models between welding current duty ratio, base current, welding speed, wire-feeding speed and wire extension were obtained, succeeding the model between the above parameters and weld pool width.

介绍了铝合金MIG焊焊接电流占空比、基值电流、峰值电流、焊接速度、送丝速度对熔宽的影响规律，并在其基础上，通过平板堆焊试验研究了这些参数对焊接干伸长的影响规律；在铝合金机器人脉冲MIG焊平板堆焊过程各焊接参数与正面熔宽之间的传递函数的基础上，采用铝合金平板堆焊阶跃试验，利用曲线拟合法辨识了铝合金机器人脉冲MIG焊动态过程传递函数，建立了焊接电流占空比、基值电流、焊接速度、送丝速度与焊接干伸长之间的对象数学模型。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。