查询词典 feed to

Feed pump system, which may comprise of one or more pumps to distribute the feedwater to the membrane units.

水泵系统，可能包括一项或一项以上的给水水泵分发单位膜。

Feed pump system, which may comprise of one or more pumps to distribute the feedwater to the membrane units.

此外，根据特定的现场配置，Memcor CP系统也可能包含下述设备

A typical lathe provides, through the feed rod, forty-eight feeds ranging from 0.002 inch to 0.118 inch per revolution of the spindle, and, through tne lead screw, leads for cutting forty-eight different threads from 1.5 to 92 per inch.

一些老式的或价廉的车床为了能够得到所有的进给量和加工出所有螺纹，必须更换主轴和变速齿轮箱之间的齿轮系中的一个或两个齿轮。

A typical lathe provides, through the feed rod, forty-eight feeds ranging from inch to inch per revolution of the spindle, and, through the lead screw, leads for cutting forty eight different threads from 1.5 to 92 per inch.

一台典型的车床的主轴没旋转一圈，通过光杠可以获得从到英寸尺寸范围内的48种进给量；而使用丝杠可以车削从1.5到92牙/英寸范围内的48种不同螺纹。

Accordingly, undertook improvement to measurement technique and unit of feet lens group, rear sight the design is staff guage of 0.02mm mobile vertical for the least scale division value, telescopic design is collimation binoculars, face of lens of feed rod lever is 1.2362m above to rear sight distance.

因此，对测量方法和尺镜组装置进行了改进，将标尺设计为最小分度值为0.02mm移动铅直标尺，望远镜设计为准直望远镜，光杠杆镜面到标尺距离为1.2362m以上。

The apron is transmits the guide screw and the feed rod turns on lathe the transportation to turn becomes the apron the translation and the impetus tool rest enters gives, controls the tool rest movement to put through, the separation and the commutation.

将光杠的运动传至纵向齿轮齿条和横向进给丝杠的传动机构，接通、断开和转换纵横进给的转换机构，保证机床工作安全的过载保险装置，丝杠、光杠互锁机以及控制刀架纵、横向机动进给的操纵机构。

Qualified plastic film in gravure printing wheel system transformation cards and membership cards should be controlled in making the two-part tensility, that is, from feed axis to feeding traction roll and roll traction from your material to your material after the participation of various ministries.

等边的塑料薄膜在瘪印轮转制卡和会员卡制息洋不主给答把持两个局部的压辛，即从给料轴到给料牵引辊和从播料牵引辊到播料后各部。

The results show that the maximal rolling pressure and the maximal strain in rolling process don't appear in the same location; the plastic strain areas locates on the both sides of the edge at the fillet, resulting in residual compressive stress reached to strengthen the purpose of rolling.In the rolling process, must be reasonable to control the feed roll.

结果表明，滚压过程中最大滚压力和最大应变不是出现在同一位置，塑性应变区域位于圆角凹面两侧边缘，冷作硬化后产生的残余压缩应力达到了滚压强化目的；滚压过程必须合理控制滚压进给量。

Production of various major domestic and international pressure feed granulators the roll, eccentric shaft, the drive wheel, Central-and pulley, bushings, flanged, bearings, shaft and various marine accessories, such as forging, and to undertake various forging processing (forging The largest diameter up to 2000 cm, the largest weighs 2,000 kilograms).

主要生产国内外各种饲料制粒机的压辊、偏心轴、传动轮、环模以及滑轮、衬套、法兰、轴承、各种轴和船用锻件等配件，同时承接各种锻件加工（锻件最大直径可达2000cm，最大的重量为2000公斤）。

First a move to pick up the part, then the actual move to feed the screw.

第一阶段是移动取对象，之后移动进料螺丝。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新