查询词典 fall-in

Consols may fall and suffragettes may rise.

证券可以下跌，女权可以兴起。

And then there are others, which fall viction of the great conspiration of the scientific establishment.

然后还有其他，其中大部分属于viction的巨大阴谋的科学建立。

I love to see you thus. Now, then, were a conspirator to fall into your hands, he would be most welcome.

"那太好了，"侯爵夫人大声说道，我就喜欢你这个样子，现在，好了，如果现在一个谋反分子落在你的手里，我们可正等着他呢。

"That is right," cried the marquise."I love to see you thus. Now, then, were a conspirator to fall into your hads, he would be most welcome."

"那太好了，"侯爵夫人大声说道，"我就喜欢你这个样子，现在，好了，如果现在一个谋反分子落在你的手里，我们可正等着他呢。"

You are at a distance R from the center of rotation, the carousel rotates at constant angular velocity ω, and the raindrops fall straight down with speed v.

你离旋转的中心还有一段很长的距离，那个传送带保持着有着尖角的速率旋转，还有那个雨滴垂直用一个v的滴下来，那里没有风。

Both agents fall to the ground, causing The Constrictor to release him.

两个密探全都倒在了地上，压缩机也放开了他。

The whole nation year fall is 200~1000mm, belong to continental climate.

全国年降水量为200~1000mm，属于大陆性气候。

After World War Ⅱ there remain territory and boundary disputes among most ASEAN countries, which fall into two types, one being the dispute on land boundary or islands sovereignty, the other on the exploring of ocean resources and delimiting of territory waters and continental shelf among them.

二战后东盟国家之间大都存在着领土边界争端，其实这种争端主要有两种：一种是东盟国家之间的陆上疆界或岛屿主权的争端；另一种是东盟国家之间因海洋资源的获取、领海及大陆架疆界的划分问题而出现的争端。

The loss should not fall on the coal company who provided for this very risk contractually.

损失不应由公司承担，其规定了这一风险。

To get the steady interface, the ratio of coextrusion flow length to height is at least l-1.5._The role of smooth flow zone is important to reduce the pressure-fall. The higher surface quality of the fluid path can make the velocity field more uniform and the interfacial offset less. However, the layer interface position was almost unaffected by the convergence angle, so for the convenience of die manufacture and extruder\'s collocation, it is fit to make the contact angle as 90°with smooth corner.

在模具结构参数中，共挤出流道的长度和模具壁面光滑程度对界面有重要的影响，根据计算结果得到了方形流道共挤出段长度与高度比的取值范围；而模具入口收敛角对界面的影响不大，在实际生产中为了模具制造和共挤出机布置的方便，可采用圆滑过渡的90°入口角。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新