查询词典 extrusion

Aimed at generator pole ′s feature,branching indirect extrusion process of generator pole was analyzed, the combined hot-cold extrusion processing of generator pole ,hot directed-extrusion and precision shaped is constituted.

在分析爪极分流式反挤压工艺的基础上，针对爪极零件特点，制定出爪极热挤压精密成形新工艺：热锻正挤压成形+冷精整，并进行了相关模具设计。

The condition of numerical simulation on extrusion deformation is that the extrusion ratio is 4100, preheating temperature of billet is 300450 ℃ and extrusion ram speed is 220 mm/s.

模拟采用的挤压变形条件为：挤压比4~100，锭坯预热温度300~450 ℃，挤压杆速度2~20 mm/s。

The company has vertical semi-continuous casting production lines, capable of producing all kinds of diameter of the circle and a square with deep processing of high-quality magnesium alloy billets deformation; extrusion production line can produce all types of magnesium alloy extrusion sacrificial anode, the sacrificial anode aluminum, zinc alloy sacrifice Anode and a variety of magnesium alloy extrusion products.

公司拥有立式半连续铸造生产线，能够生产各种直径的圆形和方形高品质深加工用变形镁合金坯料；挤压生产线可生产各类挤压镁合金牺牲阳极、铝合金牺牲阳极、锌合金牺牲阳极和各种镁合金挤压产品。

At first step, the processor before the deformable body contact the end face of cone die cavity regarded as an extrusion process. The minification of core boss's cross-section regarded as compressibility of direct extrusion, which acted as definition factor when construct the Direct Extrusion Model element. Another step, the model element of flat punch extrusion on wedge piece process was constructed when propose the process of deformable body overflow die corner. In this way the spherical end face of blank looked as cone end face one, t he approximate treatment is one of originality innovation in this paper. At last, the two elements have been connected and constructed the model element of cone boss part's deformation in the open die forging.

对于锥形凸台成形的第一个特征时段，即坯料和锥形凸台型腔的端面接触之前的变形过程，本文将凸台的截面缩小率转换成挤压成形的压缩率并以此为界定，建立了不同截面缩小率时的锥形模正挤压的模型单元；对于锥形凸台成形的第二特征时段即锥形模的角部充满过程，在详细考察锥形型腔端面对变形过程影响的基础上，将变形体的球形端面近似成锥面建立了平冲头挤压楔形体的模型单元；最后将前述两种模型单元有机连结，构建了开式模锻中整个锥形凸台成形过程的定量描述。

Finally, the best values of the diameter of prefabricate hole and extrusion speed is determined through optimize simulation results,In the end, forming experiments study of cold extrusion is processed, experiments results shows that internal thread of C195 knuckle axis can be formed by cold extrusion method, and the extrusion torque is varied when diameter of prefabricate hole and extrusion speed is a series of different value.

最后对挂钩轴内螺纹的加工进行了一系列的实验研究，经过多次实验的失败反复，最终挤压加工出了符合要求的内螺纹；实验结果表明该零件内螺纹时可以采用冷挤压成形方法加工的，并且验证了成形过程中挤压扭矩是随着工件底孔直径和挤压速度的变化而变化的。

Exhibits:Plastil soft\rigidpipe drink straw pipe extrusion machine, Plastil imitate rattan extrusion machine, Plastil making granule(single/twin screw)extruder, Plastil flat\solid super plank extruder, Plastil soft rigid abnormal profile extrusion machine, TPU\TPR Rubber band extrusion machine, PP Bale strap extrusion machine, PP\PC Hollow shutter extrusion machine

展出内容：塑胶软、硬管、饮料吸管押出机，塑胶仿藤押出机，塑胶造粒押出机，塑胶片、板、超厚板押出机，塑胶型材押出机，TPU、TPR橡筋押出机，PP打包带押出机，PP、PC中空板押出设备

In this dissertation the"Penalty"finite element method was employed to compute the velocity of the three-dimensional flow of power-law fluid in a profile die. In order to decrease the needed computer memory and raise the stability of numerical simulation, a set of decoupled methods such as PFEM, pseudo-body force method and transformation of momentum equation to the elliptic equation was developed to establish the general finite element equations to compute the distributions of velocity and viscoelastic stress of the three-dimensional viscoelastic flow of the Phan ThienTanner fluid in a profile die. During numerical simulation of the extrudate swell of the PTT fluid, the flow in the die and out of the die was analyzed separately, which demands less computer memory. The key techniques used in numerical simulation of the three-dimensional extrusion from dies such as decision of boundary conditions, creation of initial velocity field, selection of penalty factor, high Weissenberg number problem , regeneration of the free surface were studied in detail.

中文题名聚合物异型材口模挤出三维流动研究副题名外文题名 Study on three-dimensional flow of polymer melts during the process of profile extrusion from dies 论文作者涂志刚导师柳和生包忠诩教授学科专业材料加工工程研究领域\研究方向学位级别博士学位授予单位南昌大学学位授予日期2001 论文页码总数148页关键词挤出成型聚合物材料挤出口模聚合物异型材馆藏号BSLW /2003 /TQ320 /9 本文建立了求解挤出口模内幂律流体流动速度场的通用三维罚有限元模型；对于非线性粘弹性的Phan Thien-Tanner流体，为了降低模拟计算对计算机硬件的要求，并使模拟计算更加稳定，采用了一种去耦算法，包括罚有限元方法、拟体力方法和动量方程的椭圆类方程转化方法，并建立了求解速度场和粘弹性应力场的总体有限元方程；对于PTT流体的挤出胀大问题，提出了挤出胀大熔体口模内外分离模拟法，这样可以显著降低数值模拟对计算机硬件的要求。

And objective parameters (texturized degree, color, hardness, springiness, chewing, water absorption, yield, etc.) were investigated in the high moisture soy protein extrusion process, and the statistical models of system and objective parameters were built, using the step-by-step regression analysis; A comprehensive evaluation of the products, and the process optimization of high moisture extrusion were obtained,using factor analysis; Secondly, residence time distribution and soy isoflavones losses kinetics were studied in the high moisture extrusion; Finally, chemical bonding process, the micro-structure and protein secondary structure changes were investigated in the texturization of soy protein, then the mechanism assumptions of texturization soy protein by moisture extrusion were proposed.

本文对大豆蛋白高水分挤压组织化技术和机理进行了研究，研究内容包括：首先采用系统分析法，研究了大豆蛋白高水分挤压过程中，挤压机操作参数(螺杆转速、物料水分、喂料速度和机筒温度)对系统参数(系统压力、扭矩、单位机械能等)、目标参数(组织化度、色泽、硬度、弹性、咀嚼性、吸水率、产量等)的影响规律，建立了各因变参数的统计模型；采用因子分析法对产品进行了综合评价，并对高水分挤压组织化工艺进行了优化；其次，研究了大豆蛋白高水分挤压中的停留时间分布以及大豆异黄酮的损失动力学；最后，研究了大豆蛋白组织化过程中化学键、微观结构和蛋白质二级结构的变化规律，提出了大豆蛋白高水分挤压组织化的机理假设。

Using the finite element method and based on finite element simulation of profile extrusion process, the effect of local extrusion ratio, die land area and the distance between extrusion cylinder center and die opening center on mental flow velocity is studied. The deformation flow laws on profile extrusion process are obtained.

本文采用有限元方法，以型材挤压过程的有限元模拟为基础，研究了局部挤压比、挤压带面积和模孔距离对金属流动速度的影响，获得了型材挤压过程的变形流动规律。

By using the UG top down assembly modeling technology,and optimizing the design parameters of extrusion die for pipe products,the parameters SQL database of extrusion dies was established.Microsoft Visual Studio.net 2003 MFC was chosen as the development platform of the system,and an intelligent parametric design system of extrusion dies based on UG was designed,which can automatically generate 3D extrusion die assembly parts and graphics.

应用UG自顶向下的装配建模技术，对挤出模头进行参数化设计，建立智能挤出模头参数SQL数据库，采用Microsoft Visual Studio 。net 2003环境进行MFC编程，构建一个基于UG的管材挤出模头智能参数化设计系统，在UG中自动生成三维挤出模头零件和装配图。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。