查询词典 extruded

In common glass fiber reinforced polyolefine pipe, when the volume faraction is less than the critical value, the glass fiber can not act as reinforcement, on the contray, it would reduce the whole intensity of the compound material. However, when extruded in combined stress field, the extend intensity of the compound system increases when the volume fraction of glass fibers is less than the critical value. When the glass fiber volume fraction is higher than the critical value, the required glass fiber volume fraction of compound fibers extruded in the combined stress field is less than theory value.

一般玻璃纤维增强管材在常规挤出时当添加的玻璃纤维体积含量小于临界体积分数(当添加的玻纤的复合体系拉伸强度等于基体聚合物材料的拉伸强度时的玻纤体积分数)时，玻纤起不到增强的作用，反而会使复合材料的整体强度降低；但在复合应力场下挤出时，当添加的玻纤含量小于临界体积分数时，复合体系的拉伸强度不但没有降低反而升高了；当添加的玻纤含量大于临界体积分数时，复合体系要达到同样强度，经过复合应力场的玻纤增强管材需要的体积分数小于理论值。

With GLF, outline font rendering can display wire frame, solid, and both extruded wireframe and extruded solid.

以GLF，你可使轮廓字体的渲染展现出框架、实体或两者兼有的效果。

The result indicated that Extruded-soybean to rePlace the fish meal is satisfied with the raccoon dog winter fur grows, does not affect the raccoon dog fur quality.Keywords: Raccoon dog; Extruded-soybean; Fish meal; Fur quality

如果可以用膨化大豆替代毛皮动物饲料中的鱼粉，则既可以部分解决动物性饲料资源短缺问题，缓解鱼类资源紧张形势，保护生态，又可以降低饲养成本，提高养殖经济效益[2]。

The strength of SiCp/Al composites hot-pressed above and extruded below, or hot-pressed below and extruded above the solidus temperature of the matrix is higher than that of composites hot-pressed and extruded above or below the abovementioned temperature, and the strength of SiCp/Al composites hot-pressed above and extruded below the solidus temperature of the matrix is the highest.

以基体合金的固相线温度为基准，高温热压、低温挤压或者低温热压、高温挤压的复合材料的强度优于高温热压挤压或者低温热压挤压的复合材料，并且高温热压、低温挤压的复合材料的力学性能最优。

Moreover, the hot compressive deformation behavior of the RS/PM AZ91 magnesium alloy and AZ91 alloy matrix composite were also investigated, the conclusions are drawn as follows:1. The processing parameters of the atomization-twin rolls quenching technology were optimized as follows: the diameter of the nozzle 1mm, the wheel velocity 25m/s, the pressure of atomization gas 0.3MPa and Ar gas for melt injection 0.1MPa. The RS AZ91 alloy flakes exhibited fine and uniform microstructures. When the flakes were extruded at 673K, extruded velocity of 0.1mm/min and extrusion ratio of 25:1,the magnesium alloy rods with clean surface, uniform dimension and excellent mechanical properties were obtained.2. The RS AZ91 magnesium alloy powders prepared by atomization-twin rolls quenched technology exhibited fine equiaxed grains with the grain size of 1-3μm, the phase constituent included supersaturate solid solution phaseα-Mg and miner fineβ-Mg_(17)Al_(12) phase. The as-extruded materials also exhibited equiaxed grains with the size of 5-7μm and a large number of fineβ-Al_(12)Mg_(17) and fewer AlMg_2Zn phases were detected in the alloy.

本文还研究了快速凝固/粉末冶金AZ91镁合金热压缩变形流变应力行为，快速凝固/粉末冶金法原位生成Mg_2Si增强AZ91镁基复合材料，经过系统的研究，获得如下结论：1、雾化-双辊急冷法在下列工艺参数组合下：双辊线速度25m/s；喷嘴直径1mm；熔体压射压力0.1MPa；雾化气体压力0.3MPa。，可获得宏观尺寸细小、微观组织均匀细小、综合性能优良的的快速凝固AZ91镁合金细碎箔带，快速凝固箔带在挤压温度为673K、挤压速度为0.1mm/min，挤压比为25：1时，可获得的外表光洁、尺寸均匀、组织性能优异的镁合金棒材。2、雾化-双辊急冷法制备的AZ91镁合金粉末态为细小等轴晶组织，晶粒尺寸1-3μm，组织为α-Mg过饱和固溶体和微量的细小β-Mg_(17)Al_(12)相组成；粉末挤压棒材为等轴晶组织，晶粒尺寸5-7μm，组织中含有大量细小的β-Al_(12)Mg_(17)以及AlMg_2Zn析出相，室温力学性能，抗拉强度383MPa，屈服强度275MPa，断后伸长率7.5%。

In order to further understand the organization and performance of the product extruded from beryllium bronze,the nonuniformity of ingot casting organization extruded from beryllium bronze,the quenching macrocrystalline ring organization and layer structure of extrusion bars,the nonuniformity in mechanics,and extrusion effects were analyzed.

为了进一步了解铍青铜正向挤压制品的组织和性能，分析了铍青铜挤压铸锭组织的不均匀性、挤压棒材淬火后的粗晶环组织、以及挤压棒材的层状组织；同时对挤压棒材力学性能的不均匀性和挤压效应进行了分析。

Surface-treated aluminum hydroxide and magnesium hydroxide mixture, linear low density polyethylene and polyethylene grafted by maleic anhydride were melt-kneaded and extruded to produce a flame-retardant masterbatch, and then was extruded with polyamide 6(PA6) to yield PA6/SAMH/PE(50/30/20 by mass ratios)ternary composite.

采用表面处理过的氢氧化铝与氢氧化镁混合物（质量比2：1）、线型低密度聚乙烯、马来酸酐接枝聚乙烯共混挤出制成母料，然后与聚酰胺6(PA6)共混挤出即母料法制备了PA6/SAMH/PE三元复合材料。

The results show that the alloy undergoes obvious plastic elongation, the specimen fractures into four sections and the diameter changes from 16 mm to 12 mm. The fracture surfaces distribute randomly well developed and partially developed veinal patterns. The deformation behavior of alloy is non-Newtonian flow behavior. About 3% amorphous matrix of extruded specimen transforms crystal, the crystal particles with size of 10-20 mm are precipitated in the amorphous matrix, the thermostability of the extruded specimen was lowered. The failure of the alloy is mainly attributed to non-uniform viscous flow under high strain rate resulting from the hydrostatic extrusion process.

结果表明：非晶合金在高应变速率下产生了明显的塑性变形，直径从16 mm变为12 mm，断裂为4段，且样品断口上随机分布着充分发展与未充分发展的脉纹式切变带，由此可看出非晶合金的变形为非牛顿体变形行为；挤压后的样品约有3％的非晶相发生晶化，在非晶基体上析出10～20 nm的纳米晶粒，导致挤压后非晶合金的热稳定性降低；静液挤压高应变速率变形条件使非晶合金产生非均匀流变，是造成非晶合金断裂的主要原因。

Through analyzing the properties of PVC extruded materials,the main factors causing the colouration of PVC extruded product were investigated.

通过对PVC挤塑材料性能的分析，探讨了影响PVC挤塑制品着色的主要因素；从原材料及加工过程的特点，寻找控制着色产品色泽的主要因素；认为对材料的配方及配混工艺、挤塑加工工艺进行严格控制，是控制好PVC挤塑制品色泽的主要途径。

After those incisors had been extruded, a slight movement of the gingival margin in the same direction of the extruded teeth could be noted and an increase of the keratinized gingiva width was also recorded.

在这些门齿已挤压，轻微运动，牙龈缘在同一方向的挤压牙齿可以注意到，增加的角化牙龈宽度也记录在案。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了