查询词典 extensive contact

To measure the resistance of Contact 1, close both Chs. 1 and 21, then measure the resistance with the ohmmeter. To measure Contact 2, open Chs. 1 and 21, close Chs. 2 and 22, then measure the resistance again.

若要测量触点1的电阻，需要闭合通道1和21，然后利用欧姆表测量电阻；若要测量触点2，需要开路通道1和21，闭合通道2和22，然后再次测量电阻。

In this paper,taking microswitch as type mechanism of openable closed electromechanical components,on basis of constructing it s finite element model of the quick acting mechanism s static dynamic process and contact system s electrical contact process.

以微动开关作为机电元件的典型代表，通过构造其速动机构静态、动态全过程和接触系统全过程有限元模型，并以动态模型为桥梁，将静、动态过程与电接触过程这三类不同问题联为一体，构造了综合模型，仍以AK型微动开关为例，给出了计算机模拟的综合实

Purpose: To investigate the influence of retinal photocoagulation with an indirect ophthalmoscopy contact lens on corneal endothelial cells.Methods: Seventeen eyes of 17 patients were evaluated, and corneal endothelial cells were measured twice: just before retinal photocoagulation using an indirect ophthalmoscopy contact lens and 33.2 ± 10.2 days after surgery.

为研究采用间接检眼镜接触镜进行视网膜激光光凝对角膜内皮细胞的影响，对17例患者的17眼进行检测并对角膜内皮细胞检测两次：视网膜激光光凝术前和术后33.2±10.2天检测。

Contact elements play an important role in simulating mutual action between different two mediums. In order to reasonably choose parameters of contact elements experiments have been done on typical soils of Shanghai.

接触面单元在模拟岩土工程介质与结构的相互作用中发挥重要作用，参数的选择对接触面的变形规律起到关键作用，为此，作者结合上海典型土层进行接触面单元的特性实验室试验，得到其变形规律。

The four single errors exist in joint B in crank.rocker mechanism. The result indicates that the theory analysis is correct. In order to analyze the distribution of contact stress in joints, the ANSYS finite element tool is used. The situation of four single errors in joint B is analyzed. The distribution of contact stress is actually reflected. The microcosmic stress analysis is referred.

为了分析铰链在存在形位误差的情形下铰链中接触应力的分布情况，利用ANSYS有限元分析工具，通过对B铰链存在的四种可能出现的形位误差造成在装配过程中产生的接触应力的分析，真实的反映了铰链接触应力的分布情况，从而由宏观的力分析进入微观的应力分析，这也是前人没有涉及过的。

For the process of forming member gear, the machine setting parameters for Free-form generators can be determined by either direct or equivalent transformation, both methods coincide with each other. For generated pinion, the author utilizes a imaginary modified member gear to get original machine setting parameters for traditional cradle-type generator, and then establishes a mathematical model including the second and third order contact parameters of the gear pair for optimal synthesis to optimize the quality of contact transmission of the gearing.

对于成形法加工大轮可以直接或通过等效转化的办法确定Free-form型机床的调整参数，二者是完全一致的；对于展成法加工小轮，作者利用假想修正大轮的概念获得传统摇台类机床调整参数的初值，然后建立包含齿轮副二阶接触参数和三阶接触参数的优化数学模型，以优化齿轮副的啮合传动质量。

I now have a computer with this problem, AGP slot is loose, not the ordinary graphics cards and point of contact inside the contact, so there is no way to show that several times to re-inserted after the position accurately do.

我现在用的电脑就有这样的问题，AGP槽很松，显卡的金手指不能和槽内的接触点接触，这样就没办法显示，要重新插过几次后，找准方位才行。

I am afraid I have been out of contact with him but I will try my best to contact his college.

恐怕我已失去与他的联系，但我会尽力与他的学校联系上。

Such problems needing attention to of PLC application to stranding equipment as the output contact competition ,output contact capacity and alarm circuit design are pointed out.

简述PLC用户程序的工作过程，指出PLC在捻制应用中应注意的输出触点竞争、输出触点容量和报警电路设计等问题，给出解决问题的具体方法和程序，使得PLC的应用更加安全可靠。

We proposed a new p-contact scheme using Ti and ITO transparent overcoating on the regular p-contact of the proton-implanted VCSEL and obtain substantial improvement in the kink characteristics and the modulation response of the proton-implanted VCSEL shows a more open clear eye and lower jitter of 35 ps operating at 2.125 Gb/s under 10 mA bias and 9 dB extinction ratio compared to the device without overcoated.

我们提出使用新的p型电极组合，利用Ti和透明电极蒸镀在一般的p型电极上，成功的改善了质子布植的面射型雷射之kink现象，且元件亦能成功的操作在2.125 Gb/s。

Methods Clinical data of 3 cases of bile duct injury during laparoscopic cholecystectomy were analyzed retrospectively.

回顾总结3例LC术中胆管损伤的临床资料，分析3例胆管损伤的原因及对策。

These techniques are applied to the gobang.

本文将这些技术用于五子棋中。