查询词典 extensive contact

Anthropometry is one of the most important basic tasks in the apparel industry. At present, there are mainly about two methods of human body measurement, including contact measurement and non-contact measurement.

人体测量是服装设计过程中十分重要的基础性工作，现行服装行业中人体测量的方法主要有接触式和非接触式两种。

Finally, a two-mask process was attempted to extend the same concept of the chip process. Here the mask of the contact aperture was replaced by the mask of the LED pad. After etching the SiO2 and ITO in the aperture region, a lateral etch of SiO2 was made to increase the ITO contact area. Although the forward voltage of the GaN LED shows a normal value, the process yield is still low and requires further study.

二道光罩制程延伸了三道光制程的理念，只是因为透明导电层的圆孔图形，是用电极的光罩去开的，所以蚀刻完二氧化矽膜及氧化铟锡膜后，必须再做二氧化矽膜的回蚀刻，让二氧化矽再内缩进去，以增加氧化铟锡和电极的接触面积，不会造成发光二极体的顺向电压提高，但因制程良率太低，所以还须要继续研究改善。

Step 6 shows how the strokes' strength lies inward from the contact spot, as an arc to a tangent, and that head-on contact creates a right angle against the ball's flight line, 6B.

图7G。第6课展示了击球的力量来源于从触球点的内旋，是球切线上的一道弧线，迎头碰撞与球的飞行路线产生正确的角度， 6B。

By applying the difference arithmetic to solve the differential vibration model of the single-degree-of-freedom,the acceleration responses of the vibrated bevel wheel was calculated.The bevel wheel contact fault was simulated by taking it as the impulsion loading in local point.By using techniques of wavelet de-noising and demodulated resonance,gear contact character information was picked up successfully.

从齿轮的单自由度振动模型出发，运用差分算法对模型进行求解，得到斜齿轮的振动加速度响应，将齿面接触型故障等效为在局部点突加一个冲击载荷，对齿轮齿面接触型故障进行了仿真，利用小波降噪和共振解调技术分别对仿真的染噪振动加速度信号进行处理，成功地提取了轮齿接触故障的信息。

In the course of numerical calculation, the influence among asperities, the coupling problems of the variation of temperature and pressure on contact surfaces, the variation problems of the maximum temperature, maximum contact pressure, maximum stress were taken account into.

在数值计算过程中，着重考虑了微凸体之间的相互影响，温度变化与接触区域压力变化的耦合问题，最高温度、最大接触压力以及最大等效应力的变化问题。

The contact pressure and temperature distribute only at the asperities in real contact. The equivalent stresses have been interpreted in light of VonMises and Tresca principle.

粗糙实体上的接触压力和温度场分布均表现出明显的不均匀性，只分布在少数实际接触的微凸体上。

Real contact between two surfaces occurs only at the asperities, which resulted in the fact that the asperities in real contact carry high load and are prone to elasto-plastic deformation.

摩擦副接触表面的接触只发生在极少数微凸体上，导致这些微凸体承受了较大的载荷，极易产生弹塑性变形。

Under the basis of fracture topography analysis, the micro-contact model of asperity and the contact process between two fracture surfaces have been studied.

在裂缝拓扑特性参数分析的基础上，对裂缝接触的微观弹性模型和自然裂缝的实际接触过程进行了深入地分析。

Furthermore, According to the computing characteristics of explicit type of finite element method and contact-impact problems, a contact balance bisection algorithm for domain decomposition is designed and implemented.

根据显式有限元和冲击－接触问题的计算特点，设计并实现了接触均衡的分区算法。

The contact toxicity of two kinds of bitter almond on Musca domestica vicina, Mythirmna separata and Sitophilus zeamais was studied. The result showed that the contact toxicity of bitter almond oil is stronger with the increase of concentration.

含有和去除HCN的苦杏仁精油对家蝇、粘虫以及玉米象的触杀活性结果表明随着浓度的增大，精油对三种试虫的触杀活性增强。

Methods Clinical data of 3 cases of bile duct injury during laparoscopic cholecystectomy were analyzed retrospectively.

回顾总结3例LC术中胆管损伤的临床资料，分析3例胆管损伤的原因及对策。

These techniques are applied to the gobang.

本文将这些技术用于五子棋中。