查询词典 experimental

Experimental results show that the throughput of the Web server cluster system is increased by 30% with the load balancing method.

测试结果表明，本文提出的负载平衡方法应用于Web服务器集群系统中，其吞吐量提高了30%以上。

Aiming at the problems existed in the traditional experimental study and analytic methods in theory while the study was underway by the high density baler directly in laboratory, computer analysis and simulation on compressing hay in high density baler are accomplished according to the technology idea in modem design theory. The virtual prototype technology is introduced in the research.

针对在试验室条件下直接利用高密度压捆机对牧草高密度压缩过程进行研究时，传统的试验研究和理论分析方法存在的问题，本文根据现代设计理论中提出的技术思想，对牧草的高密度压捆过程进行了计算机分析与仿真研究。

Firstly, research the response of the stainless steel ball-shaped ionization chamber by experimental methods.

本文的主要研究工作有3个部分，第一部分是对不锈钢球形电离室响应进行实验研究。

At the same time, the ballistic limit curves of the Whipple shield in a velocity range from 0.5 km/s to 5.5 km/s was obtained. Comparing to the predicted curve from Christiansen ballistic limit equation, the experimental minimum critical projectile diameter is slightly greater than the prediction.

通过固定弹丸直径，改变弹丸撞击速度，寻找临界撞击速度的方法获得了铝合金Whipple防护结构在0.5～5.5 km/s撞击速度区间内的撞击极限曲线，并与由Christiansen撞击极限方程得到的撞击极限曲线进行了比较，结果表明，实验最小临界弹丸直径略大于预测值。

In comparison with the experimental data measured using the ballistic pendulum method, the present calculation method is superior to Pirri's original model.

利用这套实验装置，得到了激光与各种金属靶之间相互作用的时间和空间分辨光谱。

The experimental results show that our algorithm achieves 8.15% and 8.37% EER on BANCA database and 92.5% accuracy on the SZU CZZ database.

在深圳大学CZZ 人脸库（28 人×10 幅）上测试的识别率达 92.5%。在光照变化较大条件下测试时，系统识别率可以达到85％以上。

In this paper, the dynamic compressing experiments for the matrix material of the tungsten alloys which have been three different deforming(0%、 32.6%、 44.6%) processed have been performed by the experimental technology of separated Hopkinson pressure bar and many accurate datum have been obtained. Also the three materials have been compared with each other and analyzed. The results show that the optimized values are in a certain range to optimize the materials by changing their deforming technology. The parameters of constitutive model of Johnson-Cook have been fitted based on the datum. Then proceed to the next step, adiabatic shear band of these three matrix materials has been analyzed with finite element method. The result shows that the relations between stress and strain are different because of the differences of technical process of the three materials, but they are in great commonness in the material experiment and in great coherence in the distribution of time and space, which can been seen from the space distributing figures of plastic strain.

利用分离式Hopkinson压杆实验技术对三种不同变形量(0%、32.6%、44.6%)钨合金基体材料进行动态压缩实验，取得大量精确的数据，对比分析三种材料，结果表明通过改变变形量对材料进行优化，其变形量的优化值是有一定范围的；本论文拟合、确定了钨合金基体材料Johnson-Cook本构模型参数并对三种基体材料绝热剪切带进行有限元分析，结果表明三种材料由于工艺流程的不同，应力应变关系也不尽相同，但从塑性应变的空间分布图上体现了材料很大的共性和时间以及空间分布的一致性。

For the band-pass filter, the scattering parameters, including the insertion and return losses, has been calculated by means of electric circuit simulation. In addition, we have also carried out the experimental studies.

我们经由电路模拟来计算带通滤波器的介入和反射损失，此外，我们也完成了实验，且由模拟和量测相近的结果，我们更可确定电路模型的正确性。

The experimental results indicate that the revised narrow banding algorithm is robust.

实验结果表明，改进的窄带算法具有较好的鲁棒性。

The simulation indicates that dielectric constant warp is key factor to the design and preparation of chip mulilayer bandpass filter. The simulations were shown to be in good agreement with the experimental results.

模拟仿真表明：低烧材料的相对介电常数偏差是器件设计制备中的关键要素，仿真优化结果与LTCC试验样品的测试结果吻合较好。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。