查询词典 experimental method

The experimental setup for the turbulent jets in crossflow is designed, and the hot wire anemometry IFA 300 is used to measure the velocity field and the turbulent kinetic energy, and the computational result matches experimental measurement reasonably well. The experimental result is very important in the analysis of the flow field, deduction of the equation of the jet trajectory, check of the turbulence model and validation of the numerical method.

首先，建立了用于测量横向紊动射流的实验台，并利用IFA 300型热膜风速仪系统测量了多种工况下的流场，并将速度、湍动能结果与数值计算结果进行了比较，实验结果与数值模拟结果吻合较好，从而为分析流场特性、确定射流轨迹、比较湍流模型以及验证数值计算方法提供了依据。

The basic principle, advantage, disadvantage and the improvement for measuring liquid surface tension with different methods were described. The methods were capillary rise method, Wilhelmy plate method, pendent drop method, drop volume method, maximum bubble pressure method. The problems in the surface tension measurement of wide temperature and pressure range, the chosen of experimental methods and the development tendency of these were introduced especially in this paper.

本文着重介绍了几种液体表面张力的测定方法（包括毛细管上升法、Wilhelmy盘法、悬滴法、滴体积法、最大气泡压力法），包括这几种方法的测定原理、优缺点及改进方法，特别指出了宽温度和压力范围的表面张力测定存在的问题，实验方法的选择及表面张力测定方法的发展趋势。

This article, through summarizing the progresses in the evapotranspiration (ET0) methods research, analyzes representative ET0 computation methods emphasized on three periods of the world: modificative Penman, Penman-Monteith and standard ASCE-PM. We take 20th century 90's last stages and 21th century initial period's world newest 19 experimental achievements with lysimeter's actual value rating ET0 value as the foundations, analyzing general usage of the ET0 computational method regarding the different climatic conditions. Although the effect of PM method application is desirable in many areas, many local effects are still unsatisfactory; the method MP and so on are more suitable in part of areas; the PM and MP method are not popular, the special attention must be paid to the standard ASCE-PM method. In brief, these kinds of half theory (semi-empirical) methods only suit in certain areas.

通过对ET0计算公式研究进展的总结，分析了在世界上三个时期比较有代表性的计算蒸发腾发量(ET0)的主要公式：修正Penman公式、Penman-Monteith公式及标准ASCE-PM公式；以20世纪90年代末期和21世纪初期世界上最新的19个用Lysimeter实验值率定ET0计算值的实验成果为基础，对于不同气候条件下ET0计算方法的普适性分析评估认为：虽PM公式应用效果较好的地区较多，但也有不少地区效果欠佳，MP等公式在一部分地区较好，PM与MP公式并非普适性的，要特别关注标准ASCE-PM公式，总之，这类半理论公式均有一定的地区性。

In this paper ,we utilize the imagery with greater 1 meter resolution which is so called very high resolution as experimental data and do the research of ribbon road and simple building roof , and we talk about the process and method of extraction from high-resolution remotely sensed imagery :the representation of road and building in high-resolution image is analyzed ;a method of semi-automatic extraction for ribbon road based on angular texture signature and profile matching is promoted ;a algorithm for road extraction based on Snakes model is compared and analyzed ;the method of object-oriented image analysis and classification is introduced and we utilize this method to extract simple building roof semi-automatically ;the algorithm of road extraction is implemented as prototype system ;finally , the practicability of above-mentioned method are evaluated .

本文以分辨率大于1米的超高分辨率遥感影像作为试验数据，以具有一定宽度的带状道路和简单建筑物屋顶作为研究对象，探讨分析了高分辨率遥感影像中地物要素的半自动提取过程和方法：分析了高分辨率遥感影像中道路和建筑物的特征表现；提出了一种基于角度纹理特征和剖面匹配的带状道路半自动提取方法；对比分析了基于Snakes模型的道路提取算法；介绍了面向对象的图像分析和分类方法，使用该方法对简单建筑物屋顶进行了半自动提取；以原型系统方式对道路提取算法进行了实现；最后结合试验，对上述各种方法在实用性方面进行了评估。

Using the one-atom theory, the electronic structures of Pt-electrocatalyst with fcc structure was determined as follows:(5dn)6.48 (5dc)2.02 (6sc)1.48(6sf)0.02. Compared to the result obtained by the first-principle method such as FP-LMTO, CASTEP, their results are in good agreement with each other. Comparing the calculations of physical properties such as lattice constants, cohesive energy and bulk modulus by OA method and first-principle method, the result obtained by OA method is in excellent agreement with experimental value, but the result obtained by first-principle method is not accordable. The relationship between the electronic structures and catalytic performance was explained qualitatively by OA method and first principle method according to its electronic structures. Because the d-orbital vacancies increases and static density is high around Fermi energy band, Pt has good catalytic performance.

摘 要：依据纯金属单原子理论确定面心立方结构电催化剂Pt的电子结构为(5dn)6.48(5dc)2.02-(6sc)1.48(6sf)0.02，与采用第一原理的FP-LMTO和CASTEP等方法所计算的电子结构相比较，其结果非常相近；由OA理论和第一原理方法计算的晶格常数、结合能、体弹性模量等物理参数进行比较，OA理论计算的结果与实验值较符合，而第一原理方法计算的结果与实验值相差较大；在此基础上用OA理论和第一原理方法研究了Pt的电子结构与催化性能的关系，由于d带空穴增多和费米能级附近态密度较高，导致金属Pt的催化性能很好。

Composition of suspension will chang from titanium monoxide to titanium dioxide during standstill procedure. Experimental results show that the proposed method can successfully prepare the anatase phase of titanium dioxide .In the photocatalysis experiment, the prepared titanium dioxide nanofluid absorbs the Ultraviolet when light wavelength was 360 to 380 nm. Adsorption experimental results show that the efficiency of absorbing methylene blue using TiO2 is higher than that for TiO2 (Degussa P-25) or ZnO. Depigmentation of methylene blue experimental using TiO2 can depigmentize methylene blue reach 100% in 60 min.

悬浮液所含之奈米颗粒在静置过程中，成份方面会由似一氧化钛转变为二氧化钛；在结晶组成方面，所制备之二氧化钛颗粒之结晶组成为锐钛矿结构；在光催化方面，所制备之奈米二氧化钛悬浮液在光波长360nm~380nm时产生吸收紫外光现象，在吸附实验中本制程所制备的二氧化钛颗粒的吸附效果优於商用的二氧化钛及氧化锌，在亚甲基蓝的脱色实验中本制程所制备的二氧化钛颗粒能在60分钟内达到脱色率100%。

Chicken feed of model 661 is regarded as raw material of pellet feed, the influence that experimental factors including modulation-character temperature, modulation-character moisture, grease-additive quantity, and comminuting granularity have on making pellet quality, productivity, and electricity consumption. UG and ANSYS are regarded as simulating circumstance in finite element analysis, for problem on service life of the machine, evaluation index that average stress of a series of parameterized loop die is regarded as service life of hoop standard granulator is achieved by dynamic, static, and thermal structure coupling analysis for key part: loop die of the machine. For every influencing factor the experimental arrangement of array and combination is made by adopting optimizing idea and method of experimental design, the aim of quantification analysis is strived to arrive.

在试验设计中，采用正交试验的方法，以611型鸡饲料作为颗粒饲料的原料，分析混合饲料的调质温度、调质水分、油脂添加量、粉碎粒度等试验因素对制粒质量、生产率、电耗的影响；有限元分析中以UG、ANSYS作为仿真环境，针对制粒机使用寿命的问题，通过对环模制粒机中的关键零件环模进行动力、静力、热结构耦合分析，获得一系列参数化后的环模的平均应力作为环模使用寿命的评价指标；以实验设计的优化思想和有限元分析方法对各个影响因素作了排列组合式的实验安排，力求达到量化分析的目的。

The method of CFD numerical simulation is employed to replace experimental investigation. Hence, STAR-CD of the commercial software is used to simulate the outer flow field and heat transfer performance of integrated heat sink with heat pipes cooled by airflow. It is found that simulated results agree with experimental results well, which indicates that simulation method is reasonable and reliable. Further, simulated computations for different fin thickness, fin pitches and air velocities are performed to analyze their effects on heat transfer performance of heat sink. Finally, a new optimized structure of integrated heat sink with heat pipes is provided to meet future demands for cooling CPU and its heat transfer is also evaluated. For multi-heat source and higher dissipation power of electronic devices, the integrated heat sink with heat pipes attatched fins stagged in different positions of channels is presented and its flow and temperature fields are also simulated to enhance heat transfer. As a conclusion, all mentioned above are useful for the design of heat sink with excellent efficiency of heat dissipation and further research.

应用商业软件Star-CD对CPU集成热管散热器的外部流场和传热特性进行了数值模拟，将数值模拟结果和试验结果对比，验证了所提出的数值计算方法是可靠和可行的；利用此数值模拟方法对CPU集成热管散热器在不同散热翅片间距、厚度和气流速度下散热器的流动与传热性能进行了数值计算，分析了这些参数的变化对散热器传热性能的影响；针对未来CPU冷却的要求，确定了与最优气体流速匹配的最佳翅片间距、厚度的CPU集成热管散热器的新结构；利用试验评测了根据数值模拟提供的新结构开发出的新CPU集成热管散热器的传热性能；最后在场协同强化传热的理论的基础上，对CPU集成热管散热器的散热翅片错位排列来强化散热器的散热，满足未来大功率、多热源的电子元件的散热，为今后进一步优化散热器提供了依据。

In order to get a accurate checking result of volatilized hydroxybenzene 's amount in micro-polluted water resource,it brings forward a method of checking low-concentration volatilized hydroxybenzene ,introduces its experimental principles,experimental instruments,medicament,water sample treatment as well as its measuring method.

为了准确检测出微污染水源水中挥发酚的含量，提出了一种检测低浓度挥发酚的方法，介绍了其实验原理、实验仪器和药剂、水样处理及其测定方法，指出采用改进的方法比采用国标的方法更简单易行，提高了监测的准确度和精密度，适用于大批量生活饮用水的日常监测。

The plasma ignition threshold of metal is got through experimental and numerical study. The vapour and plasma ignition times of the target are got based on the equation of heat conduction and cascade model. We suppose that the plasma is ignited when generations of new electrons are born in vapour generation time. The influence of temperature on the thermodynamics and optics parameters of material also have been considered in the model. The resulting theory has good agreement with the experiment and overseas report. A blade method to measure the laser spot is given in this paper with validation and error analysis. The plasma threshold of metals in atmosphere and water ambients both are diagnosed with the light deflection and piezoelectric transducer. A Q-switched pulsed Nd:YAG laser operating at infrared (1064nm), visible(532nm) and ultraviolet (355nm) wavelengths has been used. Al、Fe、Cu are used as targets and get a similar results with both method. Theoretical and experimental analyses are applied on the influence of wavelength on the threshold have been done, both of which have shown that the plasma threshold of metals decrease as the laser wavelength increases; The plasma threshold of metals are higher in water than in air and the pressure of the shock wave in water is five times higher than in air .

从热传导方程和雪崩电离机制出发，假设当电子增值210倍时，考虑了温度对材料热力学和光学参数的影响时，得到了气化和等离子体点燃的时间，利用该模型进行计算得到的结果与国内外报道及自行通过实验测得的阈值基本一致；提出了利用刀刃法测量激光光斑面积的方法，并通过实验进行了验证和误差分析；利用光偏转装置和压电换能器分别对空气和水中金属等离子体点燃阈值进行了实验诊断，激光器均为调Q－YAG激光器（波长1064nm，532nm，355nm，脉宽10ns），靶材分别为Al、Fe和Cu，两种测试方法得到的等离子体点燃阈值基本一致；本文从实验和理论计算两个方面讨论了波长对等离子体点燃阈值的影响，均得到了等离子体点燃阈值随著波长的增加而减小的结论；对空气中和水中不同环境下金属等离子体的点燃阈值进行了比较研究，得到了金属在水中的等离子体点燃阈值比空气中的大，且水中产生的冲击波的压强是空气中的5倍左右的结论。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。