查询词典 eutectic

It is found that atomic densities of hypo-eutectic alloy increased and coordination number decreased with Si% rising, and there was a maximum of atomic density at eutectic composition.

发现在亚共晶成分范围内，随着Si量的升高，合金熔体原子密度升高，配位数下降，合金的原子密度在共晶处达到极大。

Sb can combine with Cu and P to form a low melting point compound which lowers the melting point of binary Cu-8P eutectic alloy by nearly 200℃. Bi and Cu can create compounds with low melting point(270℃) distributing at the boundaries and that is the reason why the melting point of (Cu-8P)-Bi is lower than that of binary Cu-8P eutectic alloy. The eutectic cluster can be refined with the addition of Fe, and that is the reason why the addition of Fe can decrease the melting point of Cu-8P alloy. Two means of decreasing the melting point of Cu-8P are found.

一定量的Sb与Cu， P形成低熔点相，从而大幅降低了Cu-8P合金的熔点，使其熔点降低近200℃；加入少量Bi后， Bi与Cu在共晶团晶界上形成熔点为270℃左右的低熔点化合物，且Bi的加入明显细化Cu-8P合金共晶团，从而使Cu-8P合金的熔点降低；加入Fe能明显细化Cu-8P合金的共晶团，使层片间距由8μm减为2μm以下，并使共晶团由层片状向短棒状转变，虽然Fe与Cu形成熔点为806℃的高温相，但Fe的细化作用使得Cu-8P合金的熔点降低，但降低幅度不大。

Cooling-curves of different composition after ultrasonic blend were measured with the guide of theory forecast results of the binary system of capric acid and myristic acid. The experiment phase diagram was protracted, eutectic temperature and composition range were discovered of the binary system. Phase change properties of eutectic composition were tested with DSC, the change of the wave shape of eutectic composition after 300 thermocycling was tested with IR.

以癸酸-十四烷酸二元体系的理论预测相图为指导，测量了该体系不同组成超声波混合后的步冷曲线，绘制了该体系的实验相图，判断出最低共熔温度与组成范围；采用DSC测试最低共熔组成的相变性能，采用IR检测最低共熔组成300次热循环前后的波形变化。

The influence of the size of pad and solder bump, the volume of eutectic solder and reflow temperature on the geometry of duplex SnPb solder joint with high Pb solder bump and eutectic SnPb fillet was simulated by finite element method with the software of SURFACE EVOLVER.

应用SurfaceEvolver软件，对含高铅焊料芯片凸点和共晶SnPb焊料形成的复合焊点的形态进行了有限元模拟，考察了焊盘大小、芯片凸点尺寸、焊料体积、焊接温度等焊点的设计及工艺参数对焊点形态的影响。

Mechanisms of heat affected zone liquation and liquation cracking in GH150 alloy were investigated by using varestraint test and hot ductility test in conjunction with the differential thermal analysis and optical, scanning electron microsopy. On heating,γ/C liquation take places in the HAZ above 1250℃. When the temperature reaches 1353- 1375℃, a large amount of liquid particles due to initial melting can be observed within the grains near the fusion boundary. On cooling,γ/C eutectic and γ/ Laves phase eutectic take place at 1273 and 1200℃ respectively.

采用可变拘束试验、热塑性试验、差热分析、光镜与扫描电镜观察，研究了GH150合金焊接热影响区液化及液化裂纹形成机制加热过程中温度高于1250℃的热影响区由于γ／C共晶产生液化，在温度达到1353℃（固相约至1375℃的近维区，晶内出现大量液化点冷却过程中温度在1273和1200℃时形成γ／C共晶和γ／Laves相共晶。

With increasing undercooling, the solidification microstructures of the alloys have changed, for example, grain refinement, transformation from regular rod eutectic structure to spherical anomalous eutectic grain structure with particulate morphology; while at higher undercooling, fine regular eutectic structure was observed.

随着过冷度的增加，其凝固组织发生了一系列的变化：晶粒逐渐细化，凝固组织从规则棒状共晶向异常粒状共晶组织转化，最后得到显微结构细小的胞状共晶团组织。

Al /AlLi-Mg〓Si and α/TiAl〓-Mg〓Si pseudobinary directional eutectic composites with fine structural integrity were achieved by investigating the influence of various amounts of alloying Li and Ti on the eutectic line, the preferred eutectic reaction point and the range in which eutectic structure appears in Al-Mg-Si system, through which the modification on the matrix and strengthening phase in this system was realised.

通过考察不同含量Li和Ti合金化对Al-Mg-Si系中共晶线、最佳共晶成分点及产生共晶组织的范围的影响，制备了组织完整性良好的α/AlLi-Mg〓Si和α/TiAl〓-Mg〓Si伪二元定向共晶复合体，从而实现了对其基体和强化相的调整。

TiC has a refinement to both primary and eutectic borides, some of which can act as the substrate for primary boride making refinement, the remainder inserting into the primary boride imped it growing in matrix; TiC inserting into the primary boride impedes the eutectic boride growing on the primary boride and decreases the formation of large block eutectic boride.

TiC对初生硼化物和共晶硼化物均有细化作用：一部分作为初生硼化物异质形核核心使其细化，另一部分在基体中嵌入初生硼化物阻碍其生长；嵌入初生硼化物的TiC改变了共晶硼化物依附初生硼化物的特点，使共晶硼化物分布细小均匀。

The microsturcture characteristics of M2 cast-strip were studied with such experimental methods as metallographic analysis, SEM, XRD and TEM[0]. The effect of sub-rapid solidification on the size, type and distribution of eutectic carbides in M2 cast-strip was analyzed. The effect of heat treatment temperature and its holding time on the eutectic carbides in M2 cast-strip was explored. The eveolution of metastable phase of M2C eutectic carbide during the heat treatment period and the decomposition dynamics concerned were researched. The M2 cast-strips were rolled into thin strips and the effect of deformation ratio on carbides in M2 cast-strip was examined. Then these thin strips were comparied with those that were produced by conventional technology on carbide, hardness, red-hardness and bend strength. At last the rolled M2 cast-strips were made into saw blades and their cutting performance was experimented on in tools factories and then compared with that of similar products produced by conventional technology.

采用常规金相、扫描电镜、X射线衍射及透射电镜等实验研究了M2高速钢铸带的凝固组织特征，分析了亚快速凝固对铸带中的共晶碳化物的析出类型和尺寸以及分布的影响；探索了后续热处理温度和保温时间对铸带碳化物组织的影响规律，分析了铸带中的亚稳相M2C共晶碳化物在热处理过程中的分解情况以及分解动力学；将铸带热轧成薄带，研究了压下率对铸带碳化物组织的影响，并将热轧薄带与常规工艺生产的相同规格的M2高速钢薄带在碳化物组织、硬度与红硬性以及抗弯性能等方面进行了对比；将热轧薄带加工成机用锯条后在工具厂进行了锯切性能试验，并与常规工艺生产的同类产品进行了使用性能对比。

The larger the atomic volume construction,the higher the stability of intermediate phase.There exist 4 eutectic systems with 9 eutectic reactions in Au-RE systems.A criterion exists between the reduced eutectic temperatureand the atomic radiiof RE metals:the Teu/TA values dedine linearly with the increase of rR Value and keep essentially a constant when rRE values are larger than 0.175nm (namely the atomic size differences between RE and Au are larger than 21%).

Au-RE系中存在4个共晶系9种共晶反应，简约共晶温度与RE原子尺寸之间存在一个判据：简约共晶温度随RE原子半径增大呈线性下降，但当RE原子半径达到约0.175nm(即与Au相对尺寸差21％)时，更大原子尺寸差不再影响液相线和共晶温度下降，简约共晶温度保持常数。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。