查询词典 estimating error

In this thesis, the geometry of airborne SAR and the basic compensation methods are briefly introduced. The effects of phase error on the imaging are derived, and the principal solution of motion compensation is accomplished finally.

本文首先对机载SAR的几何关系作了描述并推导了运动补偿的基本方法，本文还推导了相位误差对成像质量的影响，从而得到了运动补偿的基本实现方案。

By studying the present calculating formula of rectangular drawpiece blank size, this paper gains the major reason of inducting error,and obtains new more accurate formula,according to the same principal that surface area is equal before and after drawing.

对现有盒形拉深件坯料尺寸计算公式进行了分析，得出其误差存在的原因，并根据"坯料面积与拉深件面积相等"的原则得出了较为准确的盒形拉深件坯料尺寸计算新公式。

Based on equaling the semi-rigid connecting as the reduction of member end section bending stiffness,an optimization equivalent method is put forward on the principal of minimizing the error term between stiffness matrix of fined model and one of equivalent simple model.In this dissertation,structural fatigue cumulative damage and residual life assessment of wind-induced fatigue safety prewarning system is studied.S-N curve method and fracture mechanics method for fatigue analysis are discussed.

本文建立了高耸塔架结构中广泛使用的螺栓节点板联结节点的精细有限元模型，提出了一种优化等效的方法，以刚度矩阵的误差最小为等效原则，在把节点处杆件的半刚性联接等效为杆端截面抗弯刚度下降的基础上，得到了螺栓节点联结杆件的精细有限元模型与简化有限元模型的等效关系。

This Paper describes the calculations about mathematical and physical pendulums, the principe of produced acceleration, the adjusting and measuring methods and the error analysis methods of acceleration.

本文介绍了有关单摆与复摆的计算方法、产生加速度的原理、冲击加速度的调整与测量方法及其误差分析。

It is legal to create a Queue for a class that does not define the output operator but it is a compile-time (or link-time) error to print a Queue holding such a type.

为没有定义输出操作符的类创建 Queue 对象是合法的，但输出保存这种类型的 Queue 对象会发生编译时错误。

The optimized processing parameters including screen print and hot pressing were obtained. In order to reduce error, the method of double-face screen print in key electrode layer and stepped press were used. Ceramics are dense after sintering. The thickness of electrode is about 5μm. The test fixtures based on microstripe for SMD were design and fabricated.

采用平面电感和平板电容结构实现的LC谐振器，由于集总电感的Q值较小以及高介电常数介质基片杂散参数效应，这种结构的谐振器Q值较小；采用新的耦合结构-间隙电容耦合结构，实现谐振器和外电路的匹配耦合，使谐振器和耦合电容在同一层上实现，即单层结构，和传统的平行板电容耦合方式相比减小了耦合电容对位误差。

He overlooked a printer 's error.

他看漏了一个印刷错误。

A: I keep getting a printer error every time I try to print this picture .Do you know what the problem is?

每次要打印这张图，我的打印机就出问题，你知道问题在哪里吗？

A printer's error; to be corrected.

印刷错误；要被更正的。

A general printer error occurred while printing.

打印时发生了一般打印机错误。

Finally it offers the analysis of the fault-tolerance system as well as its test verification.

这样，运行于空间环境中的系统的设计目标就是在保证系统实时性

However, it is still difficult to find out the real reason of the increase of the keratinized gingiva during the orthodontic extrusion whether it is due to the proliferation of the gingival tissue or to its elastic nature, that is because the proliferation of the fibroblasts as well as the connective tissue changes in volume and the intra-fibers spaces were all immeasurable in most of the studies.

然而，仍然难以找到真正的原因增加的角化牙龈在正畸挤压它是否是由于扩散的牙龈组织或其弹性性质，这是因为增殖的成纤维细胞以及作为结缔组织的变化量和内部纤维空格都是不可估量的，大多数的研究。