查询词典 error

There are two sources of error: error manifested as an apparent magnification drift and error due to fringe tracing.

两种误差来源：放大倍数的改变引起的误差，图像歧变引起的误差

Point out the electromagnetism signal produced by human campaign not be noise completely, in which, part has formed useful signal. Analyse through error theory, have gotten the mathematics relation of phase error and apparent resistivity error.

引入CSAMT的理论，对MT勘探中电干扰和磁干扰进行了研究，从理论上证实了磁场的信噪比要优于电场的，指出人类活动所产生的电磁信号并不全部是干扰，其中一部分构成了有用信号。

The result shows that the mixed boundary condition can greatly reduce the calculation area without affecting accuracy of the solution.It is followed by the higher accuracy of Dirichlet boundary condition which makes the boundary error greater when measured points is near the boundary, so we must take a sufficiently large border region.The homogeneous boundary condition has relatively large error, but the use of non-triangle poles devices makes apparent resistivity calculation error become small, because of elimination of the effect on potential difference for the infinite boundary. In inversion, in order to save computing time, homogeneous boundary conditions are often used to perform finite element forward calculation.

结果表明，混合边界条件精度最高，可大大缩小求解区域而不影响计算精度，其次是Dirichlet边界条件精度较高，但测点越靠边界误差会越大，必须取足够大的边界区域，齐次边界条件的误差比较大，但如果采用非二极装置，通过电位差计算得到的视电阻率，由于无穷远边界对电位差的影响基本消除，视电阻率计算误差与混合边界条件下的接近，在反演中，为了节省计算时间，经常使用齐次边界条件进行有限元正演。

The arc data interpolation error by secant, tangent and chord, and the smallest error by secant mode is analyzed in this paper. The relation between the maximum radial error and arc radius and approach step-length in the secant mode of arc data interpolation in CNC system is detailed.

在分析数控系统圆弧数据插补割线方式较切线、内接弦插补方式误差更小的基础上，讨论了数控系统圆弧数据插补割线方式中最大径向误差与圆弧半径和逼近步长的关系。

Finally, an autocollimator and a high precise measuring head were used in the measurement of the displacement straighness and the the error of the lifting displacement, respectively. The experiment results show that the error of the displacement straighness is smaller than 1 and the error of the lifting displacement is less than 0.02 mm, which shows that the structure achieves the design desire completely.

用自准直平行光管和高精度测量头分别检测了平台的位移直线度和升、降位移误差，实验结果得出，该机构的位移直线度误差小于1，升、降位移误差小于0.02 mm，达到了平台设计要求。

The average error, maximum error and the error standard deviation regarding the test data decrease by 37%(45%), 34%(40%) and 35%(40%), respectively.

对测试数据的平均误差、最大误差和标准差较传统ANFIS分别下降了37%(45%)， 34%(40%)和35%(40%)。

Based on the criteria of roundness error, the definition of the circumscribed circle and inscribed circle with the least roundness error was given. The solution to the circumscribed circle and inscribed circle with the least roundness error was proposed when they met with the criterion of obtuse triangle.

根据圆度误差评定的判别准则，给出具有最小误差的外接圆和内接圆的定义，并提出了解决具有最小误差的外接圆和内接圆满足钝角三角形准则时的误差评定方法。

On the basis of analyzing the scan error of a pentaprism, the principle of scan error compensation is put forward, and the quantized formulas and applying method of compensating the scan error are presented.

在分析五棱镜扫描误差的基础上提出了误差补偿原理，并给出了量化补偿公式及误差补偿原理的实现方法。

Error compensation is an efficient way to enhance the accuracy of navigation, but error calibration is the precondition of error compensation.

误差补偿是提高捷联惯导系统导航精度的有效途径，而误差标定则是误差补偿的前提。

An algorithm of error analysis is proposed to avoid the conflict between the precision and the computational burden. The quantitative error of the reliability indices can be given through the error analysis.

论文提出了可靠性评估误差分析的实用算法，为解决蒙特卡洛模拟法精度和抽样次数的矛盾提供了有效的解决途径，为可靠性指标提供了量化误差分析。

I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""

客人们在卡罗利娜·埃凯家里，举止就文雅一些，因为卡罗利娜的母亲治家很严厉。

Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.

由著名品牌 Herm è s 设计，这件高贵的制服是香港本土制造，是我们第一套不配帽子的制服。