查询词典 error recovery

Error analysis of direct georefencing is divided into two parts: for attitude angle error, formula is determined by the error of the direction cosine matrix, for other errors, formula is determined by covariance matrix.

为了分析各误差因素对定位精度的影响，分两步建立各误差因素和定位精度的表达式，对于姿态角误差的影响，为避免欧拉角之间的耦合，按照方向余弦矩阵误差定义求取，对于其余误差的影响，采用协方差矩阵求取。

DEM Edit is the key process of the DEM data produce. Based on the analysis of the DEM data Error, this paper using the lowpass filtering method to eliminate the Random Error of DEM data, using the partial slope information detection and whole trend surface detection to detect DEM Gross Error.

DEM编辑是DEM数据生产的重要环节，本文在分析DEM数据误差的基础上，采用低通滤波的方法降低随机误差的影响，利用局部坡度信息和整体趋势面方法，实现DEM粗差的自动检测。

By re-constructing the system, the residual error dynamic characteristics of unknown input and fault signals including unknown disturbances and modelling error are obtained. The energy norm indexes of disturbance and fault signals of residual error are selected separately to reflect the restraint of disturbance and the sensitivity of faults, and the design of fault detection observer is described as an optimization problem.

通过对系统进行重构，获取了包括未知扰动、建模误差等未知输入信号和故障信号的残差动态特性，分别选取残差的扰动信号和故障信号的能量范数指标来体现其对扰动的抑制作用和对故障的灵敏性，并将故障检测观测器的设计描述为一个优化问题。

The aims of this paper are to derive the optimal error estimates of eigenpairs, i.e. the optimal error estimate of eigenvalues, and the new error estimates of velocity, pressure including the L~2 - norm and energy norm, respectively, in which the L~2 - norm estimate of velocity on anisotropic meshes has not ever been seen in the precious literature.

对于Stokes特征值问题本文不仅得到了征值对的最优误差估计即：特征值和流速压力的零模和能量模以及压力的能量模最优误差估计，其中在各向异性网格下对此问题的零模估计尚未见报道。

Keywords Error Distribution;Information Diffusion Estimation;Similarity; Error Oblate;Integral Equi-Density Error Band

误差分布；信息扩散估计；相似度；误差扁圆；整体等密度误差带

Thus, if a high resistance is required in a measurement circuit, the error analysis must account for the error due to the voltage coefficient of the resistor, in addition to all other time and temperature error factors.

所以，如果一个测量电路需要使用高阻值电阻器的话，在进行误差分析的时候，除了考虑所有其它的时间和温度等误差因素之外，还必须考虑由电阻器电压系数所引起的误差。

As shown by the experimental results, the calibration method is very effecting, easy to judge the error of LINS caused by each coefficient in its error model and the effectiveness of error coefficient compensation.

实验研究结果表明，作者提出的校准方法效果明显，容易判断每一项误差系数在LINS中对导航信号精度的影响及补偿效果，整个校准过程的时间h，适合工程上使用。

All kinds of errors that influence load sharing characteristics of gear system have been given, mainly including manufacturing and assembly error of each gear component's axis and each bearing's axis, tooth thickness error. The formulas of equivalent mesh error have been derived.

确定了影响行星齿轮传动系统均载特性的各类误差，主要包括：各个齿轮构件的中心轴线制造和安装误差、轴承中心轴线的制造和安装误差、行星架的制造误差、齿轮的齿厚偏差。

From the model, functional relationship between kinematics reliability of tool tip and every error resources was got; the contribution of each error component to the kinematics accuracy of the mechanism was analyzed and the key of all error resources was confirmed.

应用误差模型能够得出末端执行器位姿误差和各个误差源之间的显式映射关系，定量地分析各个误差源对机构运动精度的影响程度，从而确定机构中影响其运动精度的关键环节。

Then we can get the curve of Bit error rate. The influence of speed to Bit error rate in high-speed movement is studied. Results indicated that speed plays a small part to Bit error rate.

并且还研究了在列车高速运动的时速度的变化对误码率的影响，得出了速度的提高对误码性能影响不大的结论。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。