查询词典 error of measurement

According to the requirement of the high precision aspheric surface manufacturing and measurement, we design and realize a high precision manufacturing and measurement system with the technology of error compensation.

根据高精度非球面制造及测量的需求，设计并实现了高精度非球面制造及测量系统的控制软件。

According to different characteristics of CMM error distribution, single error measurement model is built by cubic spline principle and double cubic spline function.

根据三种类型三坐标测量机误差分布的特征，提出了利用三次样条原理和双三次样条函数建立测量机一维和二维相关性误差模型。

The method was proposed to compensate the residual cumulative error in the project, and the optical frequency multiplication effect on residual cumulative error is analyzed, and the model of laser heterodyne interferometric fast ultra-precision measurement is proposed.

为实现激光外差干涉快速超精密测量，通过分析测量棱镜三维运动对激光多普勒频移的影响，针对传统激光外差干涉测量模型存在的原理性残余累计误差，而且误差存在累计现象，提出了在工程中补偿残余累计误差的方法。

In the thesis, the error analysis of the instruments and error correction curve is presented, so the measurement accuracy is relatively high.

论文中分析了仪器的误差，并画出了误差校正曲线，以达到提高了测量精度的目的。

At last, it's illustrated by the theoretic ranging error curve that the relative ranging error is less than that of the irradiance measurement.

最后，给出了文中算法的理论误差曲线，分析表明该测距误差小于辐照度的测量误差。

First of all, according to the length of Hole and equipment configuration to specifications through bad error limit based on the design of the tunnel control point measurement, the number of target and observational accuracy requirements, and plans to link up on the design and error estimation.

首先根据洞子长度和仪器配置情况，以规范要求的贯通误差限差为依据，设计隧道控制测量的点位、数量、精度指标和观测要求，并且要进行图上设计和贯通误差估算。

General contact measurement error, the use of non-contact measurement is a better choice.

接触式测量一般误差较大，因此使用非接触式测量是更好的选择。

The estimating expression of theory error based on the hardware synchronous sampling measurement is advanced, and the system measuring error is analyzed.

提出了硬件同步采样算法的理论误差估计公式，并对系统测量误差进行了分析。

Simulation results show that the proposed method comes to stabilization within 50 s and that its tracking initial error can be reduced to the hectometer level with the measurement precision of 20 ns. But the traditional method requires 250 s to go to stabilization and its tracking initial error is greater than the kilometer level.

仿真结果表明，在20 ns的测量精度条件下新方法在50 s内即可进入稳定跟踪状态，跟踪起始误差也减小至百米量级，而传统时差定位方法需要250 s才能进入稳定跟踪状态，跟踪起始误差则超过了千米量级。

An evaluating algorithm of maximum inscribed circle for roundness error in the Cartesian coordinates and a measurement model of roundness error is introduced in this paper.

介绍了一种在直角坐标系下利用最大内接圆法评价圆度误差的方法，建立了圆度测量模型。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。