查询词典 erosion cycle

In water erosion area, soil erosion is caused by the several few heavy rainfalls.

在水蚀区，土壤侵蚀主要由少数几次暴雨所引起。

Then, the method to estimate cavitation erosion characteristic of high pressure piston plunger pump by analyzing impingement angle on outlet of throttling groove is put forward. That is, to hold the impingement angle range of 30°～60°as appraisal criterion of cavitation erosion characteristic on high pressure hydraulic plunger pump.4 The throttling characteristic of hydraulic control valve is studied by CFD calculation and experiment.

最后，提出了一个通过分析节流槽出口处的射流方向来评价高压轴向柱塞空蚀特性的空蚀评价方法，即将节流槽出口的射流角范围30°～60°作为评价高压轴向柱塞泵空蚀特性的标准。4对液压控制阀的节流特性进行了CFD数值计算和试验研究。

The throat floater in horse-shoe flame tank furnace is susceptible to erosion of glass fluid and the service life is shortened by the erosion.

马蹄焰窑炉流液洞挡砖易受玻璃液流冲刷侵蚀，使用寿命缩短，为延长其使用时间，需对其进行冷却。

To discuss the mechanism of controlling soil erosion by wind with standing crop stubble, combined the wind tunnel experiment with field experiment, the influence of soil erosion by wind on standing crop stubble under no-tillage practices was analyzed.

为了探讨直立作物残茬防治农田土壤风蚀发生的机理，该文利用风洞试验和野外观测相结合的方法，分析土壤免耕条件下直立作物残茬对农田土壤风蚀的影响。

It is advanced farming technology which through the implementation of reduced tillage, no-tillage technology, using crop stalks stubble ground cover to reduce soil water erosion, wind erosion, so as to enhance the capacity of soil fertility and drought-resistance .Function and role of conservation tillage technology have been proved by practice.

保护性耕作技术是相对于传统耕作的一种新型耕作技术，起源于19世纪末的美国，通过对农田实行少耕、免耕技术，尽可能用农作物秸秆、残茬覆盖地表，以减少土壤水蚀、风蚀，从而提高土壤肥力和抗旱能力的先进耕作技术。

Results showed that soil and water loss was serious, and soil erosion modulus was about 32 360 t/(km^2a) on spoil ground. Moreover, distinct gully erosion was observed on the slope.

结果表明，弃土场水土流失剧烈，侵蚀模数平均为3.24×10^4t/，边坡沟蚀现象明显。

Therefore, the resonant cavity that is composed of porous structures produced by wind erosion, water erosion, chemical dissolution and gel of SiO2 is vital to sound-producing of booming dune.

因此自然沙粒表面由风蚀、水蚀、化学溶蚀及硅凝胶沉淀等多种因素所形成的多孔状结构所构成的共鸣腔，是鸣沙发声的关键所在。

A series of erosion-corrosion test has been done to J55 steel under the influence of current of gas-liquid phase by indoor self-made devices, and the corrosion mechanism of current of gas-liquid phase to oil pipe's inner surface has been got. The results show that oil pipe's inner surface will be corroded fleetly by liquid medium and corrosion products will form on it. But at the same time, the corrosion products or protective layer will be removed from the inner surface of steel pipes under the alternate impact of high speed gas and liquid flow, and on this bare steel surface corrosion film will form again and be removed again. Thus, by these ways the corrosion is exacerbated. Surface erosion-corrosion failure comes into being with the circulation of this process going on.

本文主要在气液两相流作用条件下，通过室内自制装置，对管材钢J55做了系列冲刷-腐蚀试验，结果表明，气液两相流对钢管内表面冲刷－腐蚀的机理是钢管内表面会受到液体介质的快速腐蚀，生成腐蚀产物，同时钢管金属表面不断被具有高流速的气液相交替地冲击，不断地从金属表面脱去保护膜或腐蚀产物，裸露的钢表面又会被介质快速腐蚀形成腐蚀膜后，再被两相流冲掉，如此反复，造成管内金属表面膜的连续破坏，使腐蚀加剧，最终导致钢铁表面的冲刷腐蚀失效。

The results show that the erosion volume grows with the increment of pump pressure, there are best rock-breaking jet length, abrasive concentration and particle size. In low concentration, the erosion energy of post-mixed pulsed abrasive jet is close to the pre-mixed pulsed abrasive jet. After the external fluid is drawn in, the jet dynamic pressure increases by 7%, while pulse amplitude increases by 150%.

结果表明：冲蚀体积随泵压增大而增加，存在破岩的最佳喷距、磨料浓度和磨料粒径；在较低浓度下，后混合磨料脉冲射流的冲蚀性能较接近于前混合磨料脉冲射流；引入外部流体后射流的动压力增大了7%，脉冲幅值提高了1.5倍。

These analysis show that southern Tianshan uplift and erosion extensively from Tertiary, as a result of which the provenance of blue schist in Paleozoic accretion from north margin of south Tianshan has been curtained. With deeply erosion of Tianshan, more and more high-grade metamorphic and igneous rocks are exposed.

由此可以认为南天山的大规模隆升和剥蚀发生在第三纪以来，由于它的隆升遮挡了南天山北缘古生代增生杂岩体对库车坳陷的物质贡献，并且随着剥蚀的加深，高级变质岩和火成岩的出露越来越多。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。