查询词典 epoxy resin

With the treatment of silicone coupling on the surface of nano-Al2O3 particles and the action of mechanical decentralization and ultrasonic wave, the particles were dispersed in the matrix of epoxy resin.

采用对纳米颗粒表面进行硅烷偶联处理和机械分散与超声波振动分散相结合的方法，实现了氧化铝纳米粒子在环氧树脂中的分散。

With this model,the temperature growth process and temperature distribution of unit wall of epoxy resin,7740# glass,microcrystal glass and silicon units filled with lead styphnate were obtained by numerical simulation.

根据燃烧传热原理，建立了阵列单元燃烧传热过程的一维有限差分模型，运用此模型对装填斯蒂酚酸铅的7740玻璃、环氧树脂、微晶玻璃和硅药室单元燃烧40~80 ms过程中室壁温度成长和温度分布进行了数值模拟。

This moire effect is used in combination with photoelasticity to separate the principle stresses in the two-dimensional stress problem. The model was made by epoxy resin, its surface was covered with a printing film, which have 300 lines per inch.

以每时300道条纹的网格薄膜贴在环氧树脂模型上，采用光测法冻结技术把应力冻结下来，然后在偏振场中测取等差线，与标准网板重叠测取水平位移及垂直位移条纹图。

This is demonstrated (in form of examples of the author's own experience) for an unfilled semicrystalline polypropylene, a blend of epoxy resin with an elastomeric toughener, an injection moldable short fiber reinforced polyethyleneterephthalate, a discontinuous aligned fiber/polyethersulfone composite, and a high performance continuous fiber reinforced polymer composite system respectively.

这是表明（在表格的例子，该作者本身的经验）为一空半聚丙烯，共混环氧树脂树脂与橡胶增韧剂，一注射模压的短纤维增强 polyethyleneterephthalate ，间断不结盟纤维/聚醚砜复合材料，和一种高性能的连续纤维增强聚合物复合系统分别。

Cure behavior of F-51 epoxy resin and DAIP was studied by DSC. The influence of the different compositions on the co-cure resins morphosis and the heat resistance were researched.

研究了F-51环氧树脂和DAIP共固化的固化行为、不同配比对共固化物形态结构的影响；并研究了不同配比对固化物耐热性的影响。

Surface treatment has galvanized, nickel, gold, silver, copper, black, epoxy resin coating and heat treatment.

表面处理有镀锌、镍、金、银、铜、染黑、环氧树脂喷涂及热处理。

The microstructure morphology of the epoxy resin/nitrile rubber system and the influence of rubber kinds.

利用扫描电子显微镜等研究了环氧树脂/丁腈橡胶体系的微观结构形态以及橡胶种类、用量等对增韧效果的影响。

Using laser induced chemical deposition methods,a local micro - region quick chemical deposition of copper on a nonconductor epoxy resin substrate has been realized.

用激光诱导化学沉积方法在非导体环氧树脂基体上实现微区局部、快速化学沉铜，并用卢瑟福背散射和扫描电镜方法对镀层的形貌、性质进行了观测和分析。

And also, three new kinds of model materials with the property of normability, continuous elastic modulus and compressive strength were made for different types of rock mass, in which, sand and barite as main materials, gasoline as diluents, epoxy resin, silicone rubber and rosin as binders, of course, there exist other auxiliary materials.

根据共和隧道岩体的力学参数，以砂和重晶石为骨料，汽油为稀释剂，分别以环氧树脂、硅橡胶、松香为粘结剂，再添加其他的辅助材料研制了3种不同力学性质的相似材料，均具有可模性、连续弹性模量和抗压强度，可满足模拟3种不同力学性质岩体的要求。

As the domestic leader of epoxy resin producers,the trade mark of "Phenix Brand" is listed as one of the most well known brands in Jiangsu province and the best quality products in China.

作为国内行业的领航企业，"凤凰牌"商标是我国环氧树脂第一品牌，江苏著名商标。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。