查询词典 entrance pupil

In this paper, the research on vignetting is done and a formula for vignetting about field angle、entrance window, entrance pupil and the distance between them is deduced.

文中对渐晕做了一些研究，并推导出一个渐晕关于视场角、入瞳、入射窗以及两者之间距离的解析式。

Speckle is also the fundamental uncertainty factor in this kind of sensors. The analytic expression of centroid uncertainty limit is derived from the statistic of laser speckle, and it is shown that the uncertainty limit in RST, and also in anamorphic triangulation, is dependent on the solid angle subtended by entrance pupil as seen from the illuminated laser spot, the triangulation angle, as well as the laser wavelength. The influence of aberration of optical system and surface roughness are also discussed.(4) A method of getting the 3D edge characters based on the integrated vision system is studied.

重点研究了RST中的激光散斑现象，从散斑统计学的角度，首次推导了激光散斑引起的旋转对称三角法位移测量不确定度的极限，结果表明在光学粗糙表面上，该极限由投射激光波长，光学系统入瞳对投射光斑所张的立体角，以及光学系统主光轴与旋转轴的夹角确定；这一结论同样适用于其他变形成像的激光三角法。4基于RST的工作方式，研究了利用集成视觉系统的扫描移动来获得被测物体的低分辨率三维信息的方法。

Drift entrance pupil in laser scanning system is studied in this paper, detailing in rotated octahedron mirror.

在近代激光测试技术中多面体旋转反射扫描测试系统存在入瞳漂移的问题，带来测试误差，然而经典资料中均未作讨论。

The results show that the speckle number is only determined by the relative size of the speckle cells and the area of the entrance pupil.

在激光散斑数和光电子数较大的情况下，以往的文献一般认为光电子数服从高斯分布。

The relationship between drift entrance pupil and rotating - radius , andgle of incidence has been analysed. The accurate results are obtained.

本文在理论上推导了激光扫描测试系统中的入瞳漂移，详尽讨论了八面体旋转反射扫描测试系统的入瞳漂移问题，并且分析了旋转半径及入射角与入瞳漂移的关系，得出精确的结论。

The conclusion can be used in practice, including how to design the rotated mirror according to the requirement of measuring accuracy, to select the angle of incidence and to deal with the influence of drift entrance pupil in the design of f-θ lens.

实际应用中如何根据精度要求设计旋转反射镜、如何选择入射角、f－θ物镜设计中如何考虑入瞳漂移的影响均可利用这一结论。

The least power detected at the entrance pupil is 10-12W/cm2, spectral resolution is 2% and the measuring speed is 10 spectral lines per second.

入瞳的最小可探测率为10-12W/cm2，光谱分辨率为2%，测量速度为10条谱线/s。

In order to obtain a correct height distribution of a measured object using the conventional Fourier transform profilometry, the connecting line between the exit pupil of the projecting system and entrance pupil of the imaging device must parallel to the reference plane and in the same horizontal.

在传统傅里叶变换轮廓术三维面型测量中，为了准确得到被测物体的高度分布，必需保证投影仪出射光瞳和摄像机入射光瞳的连线与参考面平行并且在同一水平面，否则存在较大的误差。

In order to obtain the correct height reconstruction of a measured object through the traditional Fourier transform profilometry, the connecting-line between the exit pupil of the projecting lens and the entrance pupil of the imaging lens must be horizontal and set to parallel to the reference plane.

在拍摄过程中，采集完参考平面的光场后，只需要再采集一帧条纹图形，通过傅里叶变换、频谱滤波、逆傅里叶变换、相位展开等处理后就能得到物体的三维数据。采用传统的傅里叶变换轮廓术进行三维物体面型测量时，必需保证投影装置出射光瞳和成像装置入射光瞳的连线与参考面平行，并且它们的光轴应在同一平面上，才能得到较为准确的测量结果。

We focus on resolving the following problems in FTP, that is how to guarantee the measurement accuracy of FTP when the connect line between the exit pupil of the projecting lens and that of the entrance pupil of the imaging lens is not parallel to the reference, or the two pupils are not coplanar, or neither the connect line parallel to the reference nor the two pupils coplanar.

推导出了适用范围更广泛的变形条纹描述公式和相位计算方法以及相位—高度映射算法。对于传统的傅里叶变换轮廓术测量系统而言，由于要求投影仪出瞳与摄像机入瞳连线与参考面平行，而且要求投影仪光轴与摄像机光轴共面，所以它可以被看作是本文所提出系统结构在该种情况下的一种特例。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。