查询词典 electron tube

The experiment table on heat transfer of finned tube is established to test the validity of numerical simulation. The heat and temperature distribution of tube and the air around tube are measured.

为了证明以上模拟结果的准确性，建立了翅片管换热实验台，通过实验测出翅片管及其周围空气的温度分布和散热量，与数值模拟结果进行比较，从而验证了数值计算的准确性。

Torque tube (the torque tube is the tube that is attached to the mast and to the control rods).

扭矩管连接桅杆和操作臂

"On the tire with an inner tube , the valve is mounted on the tube . On the tube less tire, the valve is mounted on the wheel rim."

有内胎式轮胎气门是直接做在内胎上的，无内胎式轮胎的气门安装在轮毂上。

This exposes the tube to the ground but when the tube is pumped up the tire seals the tube.

这暴露了管到地面，但在管抽了轮胎密封管。

This exposes the tube to the ground but when the tube is pumped up the tire seals the tube.

这暴露了管地面但是，当管所抽取轮胎密封管。

I was unable to get the valve stem through the rim after the tire was partly on, so I had to remove the tire, put the tube in place and carefully mount the tire over the tube and rim without damaging the tube.

我无法得到阀杆通过环后轮胎部分，所以我不得不删除轮胎，把管到位，精心安装轮胎的管和RIM不损坏管。

With protected stuff at colligation part in order to protect tail shaft , send the tail shaft into the stern tube slowly with manual crane , during the process , we should align the tail shaft and stern tube carefully in order to protect the impact between the stern tube bearing and the screw of tail shaft .

起吊艉轴并送入艉管内：在绑扎钢丝绳的部分包上麻包布以保护艉轴后，即可起吊艉轴；然后用葫芦将艉轴慢慢送入艉管内达到预定位置，在送进过程中，要注意将艉轴对准艉管，防止艉轴承和艉轴螺纹与之相碰。

This article analyzes some regulations for safety steering column,discusses the distribution of crashing and the structures and the safety control principls with flex steering shaft,breaking steering shaft,sleeve steering pillar tube as well as ripples tube steering pillar tube.

分析了安全转向柱的法规要求，汽车碰撞能量的分配，伸缩式转向轴、可断开式转向轴、套筒式转向柱管、波纹管式转向柱管等的结构和安全控制原理。

The protecting tube (1) is not limited to the smooth-walled tube but may be a spirally corrugated tube.

所说保护管(1)并不限于平滑管，还可以是螺旋状波纹管。

Details punching process different forms of the characteristics and difficulties, an analysis of the tubes in the process of punching force and deformation of the tube, giving details of the tube clamping and reverse punch the need for pre-deformation and design methods, introduction of specific modules can be combined Guanzi punching die structure design and manufacture of key components, the introduction of simple structure, low manufacturing costs, assembly convenience of fast and flexible, applicable to many varieties, short-cycle preparation and application of the superiority of the scope of After the structure of the tube to improve the punching mold, significantly broadens the scope of the existing pipe punching process and the application of mold capacity.

工程类的汉译英，帮忙翻译下谢谢详述了管子冲孔工艺不同形式的特点和难点，分析了管子冲孔过程中的受力情况以及对管子变形的影响，详述了管子冲孔夹紧及反向预变形的必要性和设计方法，具体介绍了单元可组合式管子冲孔模具结构的设计及关键零件的制造，介绍了具有结构简单、制造成本低、组装方便快速灵活、适用多品种、准备周期短的优越性及应用范围，经过结构改进的管子冲孔模，大大拓宽了现有管子冲孔工艺范围和模具的适用能力。问题补充：请不要用在线翻译的功能搞，翻得很不好

You can do some assertiveness training.

你可以进行一些自信训练。

We were well on the path to making a rear-wheel-drive global platform," says Mays."

我们正致力于建立一个后轮驱动的平台，"Mays这样说道。"