查询词典 electro-discharge

Antephase electro-acupuncture treatment can prevent the postopadhesion of muscle, the effect of electro-acupuncture is not significant in anaphase.

电针早期干预对肌肉粘连的形成有较好的预防作用，而后期对已经形成的粘连治疗效果则不明显。

ROM is clearly enhanced by electro-acupuncture in Antephase, but the effect of electro-acupuncture is not obvious in anaphase.

电针早期干预能够明显提高实验性粘连家兔的关节活动度，而后期的电针治疗对关节活动度的影响不明显。3。

At present, the electro-acupuncture apparatus for basic architectonic is used for decades,but, there are still deficits in electro-acupuncture apparatus needed for study and research.

目前流通的电针仪的基本构造已经沿用数十年，存在许多不足，无法满足上述研究对电针参数选择的需要。

Thanks to the patented technology, electro-encephalic signal collection technology has been catapulted to a new high. Nonetheless, the equipment is still denied access to analyzing collected electro-encephalic signals and what it can offer doctors is only electro-encephalic waveform, namely, encephalogram.

该专利技术将脑电信号的采集技术提高到一个新的水平，但是该设备并没有将所采集的脑电信号进行分析的功能，所能呈现给医生的还只是脑电的波型即脑电图。

By combining virtual instruments technique with the test technique of electro-hydraulic servo valve, the test system of electro-hydraulic servo valve based on virtual instruments has been developed by the graphics software-LabVIEW6.1. The test principle and method of electro-hydraulic servo valve were discussed in this dissertation. The experimental results on a Moog servo valve demonstrate that the design of electronic-hydraulic servo valve test system is valid.

本文将虚拟仪器技术和电液伺服阀性能测试技术结合起来，利用图形化软件工具—LabVIEW，研制开发出了基于虚拟仪器的电液伺服阀性能测试系统，对电液伺服阀的静、动态特性测试原理和方法进行了讨论和研究，以MOOG伺服阀为测试对象进行了静态特性测试和试验结果分析，验证了所开发的电液伺服阀测试系统设计方案的合理性。

On the basis of previously research, this paper re-probe into the mechanism of electro-chemist mechanical manufacturing process, making the rational technological parameter, and developing the manufacturing equipment. Through a lot of technology tests, get a lot of labratory data, accordingly, researched the surface feature of the electro-chemist manufacturing process, and deeply discussed its influence on the work piece feature. The last result is that: the electro-chemist mechanical manufacturing process can reduce the low-frequency component significantly, but on high-frequency component, it has little influence, having obviously positive pole flat effect. After manufacture, the tip parts on the surface of the work piece is cut off, there is micro "high land" shape, the parameter for surface roughness is reduced a lot, the surface outline of the work piece is negative, the bearing length rate is cliffy. Also the surface quality of the work piece is improved. This can help to avoid changing the shape, improve the feature of rub, gear and reduce the time to suit. This would also ensure the precision and result in a longer work piece life.

在以前研究的基础上，本论文重新探讨了电化学机械复合光整加工工艺的机理，确定了较合理的工艺参数，对电化学机械复合光整加工设备进行了改进，通过工艺实验广泛地搜集了大量实验数据，依据实验数据，多角度地研究了电化学机械复合光整加工的表面形貌特点，并且从理论上深入讨论了电化学机械复合光整加工表面形貌对工件工作性能的影响，最后得出的结论为：电化学机械复合光整加工对工件原始表面的低频成分有较大程度的降低，而对高频成分影响较小，有明显的阳极整平作用，被加工工件表面的尖峰状凸起被去除，工件表面呈现出微观&高原型&，表面轮廓不平度高度特性参数大幅度降低，工件表面轮廓分布集中，且呈负偏态，轮廓偏斜度为负值，轮廓支承长度率曲线陡峭，工件的表面质量得到综合改善，这对提高零件的抗接触变形能力、改善摩擦、磨损性能、降低工件的磨合时间、提高工件的精度保持性、延长工件的寿命均有利。

Aiming at the deficiency of the conventional electro-hydraulic proportional valves performance,such as response time and response speed,an ultra-high-speed electro-hydraulic proportional valve is proposed,and the structure of an electro-mechanical converter is put forward using eight pieces tegular Halbach magnet array with gaps.

针对常规电液比例阀在响应时间和响应速度等性能上的不足，设计了一种超高速电液比例阀，并且提出了8片瓦型有气隙Halbach磁化阵列型动圈式电-机械转换器。

Electro-hydraulic servo valve is the key component of electro-hydraulic servo system, the test of its static and dynamic characteristic is significant in theories and test research of electro-hydraulic servo system.

电液伺服阀是电液伺服系统中的关键元件，其静态和动态特性测试在电液伺服系统的理论与实验研究中具有十分重要的意义。

Wire electrode based on the trajectory of the different forms of control, WEDM can be divided into three types: one is shaped by the imitation controlled cutting in line in advance and work to create the same shape by mold, when processing the workpiece at the same time rough and on the mold clamping in the machine tool table, in the process of cutting wire electrode tightly against the mold on the edge of the track for the mobile, thus cutting out and die on the same shape and precision to the workpiece; another One is the electro-optical tracking control, to carry out the cutting line, before the basis of certain parts to enlarge the proportion of drawings depicts an electro-optical tracking map-processing machines will be placed in design stage of electro-optical tracking, tracking platform Photoelectric first line of graphics has always been to follow the track of the Mexican campaign, and then through the use of electrical, mechanical linkage to control the machine tool table, together with the workpiece so相似形wire electrode relative movement, thus cutting out the same shape and design to the workpiece; again a digital control, the use of advanced automatic control of digital technology-driven machine tool in accordance with the pre-processing parameters according to the workpiece geometry pre-processing procedures for the preparation of a good CNC auto-complete processing, the production does not require appearance on board the need to map to enlarge map of the previous two form of control has a higher machining accuracy and a broad range of applications, both at home and abroad more than 95% have adopted WEDM NC.

根据对电极丝运动轨迹的控制形式不同，电火花线切割机床又可分为三种：一种是靠模仿形控制，其在进行线切割加工前，预先制造出与工件形状相同的靠模，加工时把工件毛坯和靠模同时装夹在机床工作台上，在切割过程中电极丝紧紧地贴着靠模边缘作轨迹移动，从而切割出与靠模形状和精度相同的工件来；另一种是光电跟踪控制，其在进行线切割加工前，先根据零件图样按一定放大比例描绘出一张光电跟踪图，加工时将图样置于机床的光电跟踪台上，跟踪台上的光电头始终追随墨线图形的轨迹运动，再借助于电气、机械的联动，控制机床工作台连同工件相对电极丝做相似形的运动，从而切割出与图样形状相同的工件来；再一种是数字程序控制，采用先进的数字化自动控制技术，驱动机床按照加工前根据工件几何形状参数预先编制好的数控加工程序自动完成加工，不需要制作靠模样板也无需绘制放大图，比前面两种控制形式具有更高的加工精度和广阔的应用范围，目前国内外95%以上的电火花线切割机床都已采用数控化。切割属电加工范畴，是由前苏联人发明的，我国是第一个用于工业生产的国家，当时由复但大学和苏州长风机械厂合作生产的这是最早的机型叫复旦型，我们国内在此基础上发展了快走丝系统。欧美和日本发展了慢走系统LS

Electro-acoustic equipment categories: electro-acoustic device test system, characteristics of piezoelectric transducer tester, test sensitivity sorting device, sound level meter, precision signal source Sweep, Sweep audio device, the standard sound source, standard test microphone, IEC318 Simulation of the ears, mouth simulation, speakers polarity tester, telephone analyzers, such as electro-acoustic type of testing equipment.

电声器件测试系统、压电换能器特性测试仪、灵敏度测试分选仪、声级计、精密扫频信号源、音频扫频仪、标准声源、标准测试话筒、IEC318仿真耳、仿真嘴、喇叭极性测试仪、电话分析仪等电声类测试仪。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。